Subject	Greg's infeed restrictors may have saved the turbos
Posted by	fourZero on November 05, 2007 at 1:51 AM
	This message has been viewed 193 times.
In Reply To	Re: i would flush EVERYTHING... anywhere oil has passed posted by tognot on November 04, 2007 at 11:53 PM
Message	Not much brass would be able to make it through those holes even if I had circulated that oil for more than a few seconds. Just to be safe, I sprayed an entire can of brake cleaner through the oil passage of each turbo over a few sheets of white paper to see if any bearing particles were found. Thank God nothing came out. The shafts spin freely and without any hesitation or hangup. "It must suck for you to be the most retarded than everyone else here." -AzHeat 09:30:20 09/10/04 "So I nailed it, took off like an F18 from carrier. Of course the chase begained." -Tim_N/A 10:27:15 04/07/03 "Ps, I ate a real chocolate jesus today. it was kick ass. it was about 3" tall and solid chocolate. I was in heaven." - niXit 10:53:48 10/02/02
Follow Ups	Let's play "name that part in my oilpan" - fourZero 22:57:38 11/04/07 Re: Let's play "name that part in my oilpan" - Z-Tech 23:19:28 11/04/07 Second, You gotta change your sig to a oil pan - RHulme 23:28:11 11/04/07 uh that really sucks (n/m) - Ashman2k2 23:29:25 11/04/07 I was looking at the pics thinking the same (n/m) - 550HPTT 23:30:24 11/04/07 I was looking at the pics thinking I know jack about cars. (n/m) - ben7021 23:38:08 11/04/07 lol...yurp... (n/m) - Pilot.P (NZ) 02:48:00 11/05/07 Re: i would flush EVERYTHING... anywhere oil has passed - tognot 23:53:51 11/04/07 Fine. I took the oil infeed lines off the turbos and shot - fourZero 01:09:14 11/05/07 Greg's infeed restrictors may have saved the turbos - fourZero 01:51:31 11/05/07 without oilpressure I doubt it's gone through the engine - lymon 06:03:54 11/05/07 I think that's the oil pressure regulator. (n/m) - BlackholeZ 00:04:54 11/05/07 Time to raise some hell - fourZero 00:53:42 11/05/07 score one for the shop :( - spyhunterTT(nj) 06:07:38 11/05/07 I don't think the shop does anything with that. Unless - SlicktopTT 07:46:26 11/05/07 Did you not read earlier up? - fourZero 08:44:33 11/05/07 i guess you have a case then - if they messed with it - ztunerz 09:11:40 11/05/07 Missed that, only read the preview. (n/m) - SlicktopTT 09:34:15 11/05/07 Re: Time to raise some hell - tognot 08:44:41 11/05/07 Sorry to see that fourZero...such a shame. - brahmabull (CT) 09:06:18 11/05/07 LoL! (n/m) - Spongerider :) 11:01:02 11/05/07 why did they open it in the first place ? (n/m) - ztunerz 07:46:07 11/05/07 Re: why did they open it in the first place ? - fourZero 08:45:59 11/05/07 Why did they shim it though? That doesn't make sense - BigTDogg (MA) 09:11:01 11/05/07 to bump up base oil pressure - yes there is no published - ztunerz 09:14:24 11/05/07 Ah, that makes sense then. - BigTDogg (MA) 09:46:31 11/05/07 loctite FTW - aliaZ 12:09:23 11/05/07 I would recommend against turning the crank.. - Kong ZTT GT28RS MD 08:36:59 11/05/07 i agree - don't know why but i have never seen a sucessful - ztunerz 09:13:02 11/05/07 Not sayin either way to do it but if the nitride is the - 550HPTT 12:37:23 11/05/07 >>> - ztunerz 13:10:01 11/05/07
Post a Followup	You cannot reply to this message because you are not logged in.