Subject	BTW, bed-in procedure for Hawk street compounds
Posted by	kuah@splparts.com on November 03, 2007 at 4:01 PM
	This message has been viewed 106 times.
In Reply To	Sounds like the pads are glazed posted by kuah@splparts.com on November 03, 2007 at 02:47 PM
Message	"After installing new pads make 6 to 10 stops from approximately 35 mph with moderate pressure. Make an additional two to three hard stops from approximately 40 to 45 mph. Do not allow the vehicle to come to a complete stop.When completed with this process, park the vehicle and allow the brakes to cool completely before driving on them again. Do not engage the parking brake until after this cooling process is compete."
Follow Ups	Hawk HPS pads are sucks. - ENVYMYZ 17:30:01 11/02/07 Don't know about MM's but HPS's do suck compared to - zboost(NoVA) 17:36:15 11/02/07 oops, looks like i got owned... (n/m) - Keaner 17:39:25 11/02/07 I think you're the first one I've heard dislike them... - Keaner 17:39:02 11/02/07 Brakes were bled 4 times at the time of install. - ENVYMYZ 17:45:39 11/02/07 Yeah, pretty much - Broke_as_**** 17:51:37 11/02/07 The cake is a lie... (n/m) - johnnysombrero 21:50:29 11/02/07 all I know is my MM's are noisy... - inf 17:45:31 11/02/07 My MM's have been noisy as hell- - Keaner 17:54:10 11/02/07 user error (n/m) - Guapo 17:47:27 11/02/07 "Hawk HPS pads are sucks." ? (n/m) - Spongerider :) 17:56:19 11/02/07 Poor Grammar== Wicked Cool (n/m) - Keaner 17:57:41 11/02/07 Engrish.com (n/m) - Z_Cherub 20:24:52 11/02/07 hmmm i've always run MMers and slotted. - Halo Z 18:06:51 11/02/07 LOL, vatozone.....awesome - LJZTT 18:35:39 11/02/07 How do you fade brakes, on the street, in an NA? - ni[X]it 18:13:44 11/02/07 You obviously don't have 'fun' streets around you (n/m) - Keaner 18:15:27 11/02/07 Not hard - Twisties and repeat :P - bstyleZ 18:59:51 11/02/07 Amen (n/m) - Keaner 19:48:09 11/02/07 I've run tail of the dragon - ben7021 21:21:33 11/02/07 ^^^ What Nix said. (n/m) - Inzane 13:57:47 11/03/07 I agree. - ZCulture 18:28:46 11/02/07 Might be... - golden_1 18:46:12 11/02/07 Shit, I just sold my brand new MM before installing them... - Dark Diver 18:33:35 11/02/07 They are a good quiet low dusting street pad - maglito 18:38:15 11/02/07 Funny, I switched to Hawk HPS pads from my MM - AbsolutZ (OH) 20:31:50 11/02/07 Maybe it's the slotted rotors? - SactoTodd 20:39:33 11/02/07 Fair enough, but I doubt it's the rotors. (n/m) - ENVYMYZ 09:57:33 11/03/07 I have the same setup, and they are the best pad I've used. (n/m) - ZiNnYc 21:15:42 11/02/07 From speaking with Greg I believe it's the brembo rotors and - ShakaShaun(Denver) 21:27:06 11/02/07 So what did he recommend you use with those rotors? (n/m) - ENVYMYZ 09:58:11 11/03/07 I would think problems with the rotors would be evident... - thejoneZ (Sacto, CA) 21:29:25 11/02/07 Funny, i've only had good luck with Hawk HPS pads, do this > - Coz@CZP 23:19:37 11/02/07 Quite possible. I did buy these pads from Ultimate Z after - ENVYMYZ 10:00:12 11/03/07 I've had the Hawk HPS with Skyline rotors 4 yrs - RHulme 23:58:14 11/02/07 My HPS > than MM (w/slotted rotors) - RedZ 00:37:19 11/03/07 Re: Hawk HPS pads are sucks. - Slider 08:26:58 11/03/07 Axxis MM or ultimate ? (n/m) - Dark Diver 09:35:25 11/03/07 Those were Axxis Ultimate, a semi-track pad (n/m) - Guapo 09:58:15 11/03/07 Why the stoptech's if you don't go to the track? (n/m) - TTFairladyZ 18:55:04 11/03/07 Re: Why the stoptech's if you don't go to the track? - Slider 11:23:01 11/04/07 I did'nt care for the HPS pads either...they did'nt - racer2fst 08:32:46 11/03/07 Same results here. The PBRs/MMs have better initial - Yoshi 17:00:13 11/03/07 3rd. (n/m) - BradZ (FL) 00:10:52 11/04/07 They got me through the Dragon with no complaints... (n/m) - TT XTZ 10:48:34 11/03/07 false (n/m) - Spee 13:58:08 11/03/07 Sounds like the pads are glazed - kuah@splparts.com 14:47:33 11/03/07 What do the pads look like if this happens? Any fix? (n/m) - pearl5 15:41:31 11/03/07 Re: What do the pads look like if this happens? Any fix? (n/ - kuah@splparts.com 15:56:27 11/03/07 BTW, bed-in procedure for Hawk street compounds - kuah@splparts.com 16:01:07 11/03/07 Yep, proper bedding is everything - SeedyROM 16:07:00 11/03/07 Thanks for the info Kuah. Ill yank em and have a look see. (n/m) - ENVYMYZ 17:23:45 11/03/07 I found the HPS's and slotted/drilled rotors much better >> - my91z 15:37:16 11/03/07 2nd. (n/m) - ThunderZ 17:08:07 11/03/07
Post a Followup	You cannot reply to this message because you are not logged in.