Subject	here
Posted by	aliaZ on November 01, 2007 at 5:27 PM
	This message has been viewed 137 times.
In Reply To	where is the gap? Is your cast divider flush with posted by AZHeat on November 01, 2007 at 02:05 PM
Message	[ http://www.twinturbo.net/net/viewmsg.aspx?forum=general&msg_id=1878690 ]
Follow Ups	Update on SPL Z: testing out a new Accusump system - kuah@splparts.com 11:20:23 11/01/07 and some people don't think the VG is up to it... (n/m) - CRAZZEPETE. 11:23:44 11/01/07 next track day in Cali or TWS? - 300twinz (satx) 11:25:42 11/01/07 At this point, probably TWS (n/m) - kuah@splparts.com 11:31:26 11/01/07 Did you get my email? (n/m) - Eric(NJ) 11:35:40 11/01/07 Yup, waiting on the package from Speedbleeder - kuah@splparts.com 11:42:11 11/01/07 Cool, thanks. (n/m) - Eric(NJ) 11:43:49 11/01/07 nice work Kuah. Looking forward to seeing your results. (n/m) - Tu 11:31:36 11/01/07 wow, very interesting setup. GL man! (n/m) - spotz 11:53:25 11/01/07 nice (n/m) - aliaZ 11:53:47 11/01/07 cool stuff, good luck at the track! (n/m) - LJZTT 11:54:52 11/01/07 Curious - any particular reason why you run a 3 inch - The Devils Z 12:16:07 11/01/07 probably the same reason ixcr8 does the same - aliaZ 12:26:31 11/01/07 My turbos have a cast divider turbine housing - kuah@splparts.com 12:38:46 11/01/07 How so? My turbines have cast divider and it - AZHeat 12:47:10 11/01/07 i take it your running custom manifolds... - zxtuner161 21:58:13 11/01/07 do you have a dyno sheet you would be willing to share ? - ztunerz 12:59:27 11/01/07 No, plus it wouldn't be a good comparison - kuah@splparts.com 20:27:10 11/01/07 Harry -- I didn't forget your request .. my motherboard - The Devils Z 05:18:52 11/02/07 I just kept the cast divider in place of the bolt-on divider - 300zx90 (CO) 13:52:55 11/01/07 where is the gap? Is your cast divider flush with - AZHeat 14:05:50 11/01/07 here - aliaZ 17:27:38 11/01/07 Re: where is the gap? Is your cast divider flush with - Guapo 17:32:57 11/01/07 plumbing - freak152000 12:18:37 11/01/07 i think he is using that as a preluber if i'm not - ztunerz 12:26:44 11/01/07 Re: plumbing - kuah@splparts.com 12:40:06 11/01/07 Did you insulate the water and oil lines - DAYTONAZ 14:30:54 11/01/07 Nice! Good luck. (n/m) - TheTwinZ (Peru) 13:43:28 11/01/07 Glad to hear it's running again. (n/m) - SeanK (StL) 16:45:14 11/01/07 Cool. (n/m) - Boosted1 21:00:31 11/01/07 very cool (n/m) - Spee 00:11:05 11/02/07 Impressive, glad to see you guys bounce back from STL - JBender 00:19:37 11/02/07 TWS Nov 17-18, with TWS Motorsports Club - kuah@splparts.com 08:39:28 11/02/07
Post a Followup	You cannot reply to this message because you are not logged in.