Subject	So you want to end up w/ 4-5mm gap after turning?
Posted by	BlackholeZ on October 15, 2007 at 11:13 PM
	This message has been viewed 32 times.
In Reply To	Set tensioner gap to ~5MM, turn motor by hand, check again. (n/m) posted by YugoBernie (NoVA) on October 15, 2007 at 05:00 PM
Message	Thanks again Bernie! _____________Sig_____________ Live, breathe, eat, sleep Z "When Chuck Norris was denied an Egg McMuffin at McDonald's because it was 10:35, he roundhouse kicked the store so hard it became a Wendy's." "When the boogey man goes to bed at night, he checks the closet for Chuck Norris." "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "bashcomesinandpostallhiswishdomonthisin85432pagesofBS (n/m)" - Halo Z "Z32 it will get you for life" - Smitytec "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne
Follow Ups	Pull gauge for timing belt - BlackholeZ 09:46:35 10/15/07 autozone maybe (n/m) - 90tt2+2z (WI) 10:40:25 10/15/07 whatever it is - turbomaniac 11:27:38 10/15/07 2nd. (n/m) - BradZ (FL) 12:17:10 10/15/07 3rd (n/m) - Madhatter10-6 12:21:13 10/15/07 dont think u will need one (n/m) - Drk93TT 12:17:08 10/15/07 don't need one, hence Auto Tensioner (n/m) - BigTDogg (MA) 12:24:28 10/15/07 You can try a hand held scale used for weighting - AZHeat 12:50:14 10/15/07 Something everyone should have in their garage... (n/m) - BigTDogg (MA) 12:56:05 10/15/07 2nd (n/m) - Drk93TT 13:19:40 10/15/07 Re: Something everyone should have in their garage... - AZHeat 16:54:14 10/15/07 for doing what to fish? (n/m) - Spee 19:41:20 10/15/07 Never used one. (n/m) - YugoBernie (NoVA) 13:49:03 10/15/07 2nd. (n/m) - Woody75 (Denver) 14:05:45 10/15/07 So you just check the tension by hand? any pointers? (n/m) - BlackholeZ 16:28:37 10/15/07 Set tensioner gap to ~5MM, turn motor by hand, check again. (n/m) - YugoBernie (NoVA) 17:00:37 10/15/07 4 or 5mm allen wrench works well for that task. (n/m) - Guapo 17:11:19 10/15/07 Indeed. (n/m) - YugoBernie (NoVA) 17:25:32 10/15/07 So you want to end up w/ 4-5mm gap after turning? - BlackholeZ 23:13:17 10/15/07 Yes. (n/m) - YugoBernie (NoVA) 12:34:31 10/16/07 Wondered about this myself; the push/pull gauge - olyar15 15:39:35 10/15/07 Use a hand held fish scale. It is what fisher man - AZHeat 16:54:00 10/15/07 *weigh (n/m) - ZiNnYc 21:29:40 10/15/07
Post a Followup	You cannot reply to this message because you are not logged in.