Subject	Since he deleted his classified ad
Posted by	TTFairladyZ on September 17, 2007 at 11:38 PM
	This message has been viewed 35 times.
In Reply To	he didn't make it clear how bad the clutch was posted by aliaZ on September 17, 2007 at 11:20 PM
Message	If I remember correctly, he either gave a picture of the clutch disk thickness w/micrometer, or it was listed in his ad. And stated at which point in the life of the clutch when it would need a rebuild, per RPS.
Follow Ups	check out this Nismo twin plate clutch/light flywheel combo - ZEngineer 18:54:10 09/17/07 I doubt there's anyone here is using this clutch - ZEngineer 19:08:18 09/17/07 I got the exact same one here - Russell@Z1 19:21:15 09/17/07 do you have it installed or just laying around? - ZEngineer 19:58:18 09/17/07 Just sitting - Russell@Z1 21:02:22 09/17/07 so you wouldn't know if it works with OEM throw out bearing - ZEngineer 22:16:19 09/17/07 you guys able to source the disks? - AxleZTTic 20:22:29 09/17/07 We haven't looked into it. (n/m) - Russell@Z1 21:05:21 09/17/07 I have this setup - WXY 19:28:19 09/17/07 I've read the opposite about the Z32 application - ZEngineer 20:01:51 09/17/07 same with - WXY 20:24:19 09/17/07 maybe you have an adjustment problem? (n/m) - CRAZZEPETE. 11:16:06 09/18/07 Welcome Back. (n/m) - SactoTodd 22:46:19 09/17/07 i got the same thing in my jdm engine! - AxleZTTic 20:16:18 09/17/07 You can buy them here... - BradZ (FL) 20:29:24 09/17/07 shaweeeet! thanks dood!! (n/m) - AxleZTTic 20:40:53 09/17/07 Yeah, but if you pay with a CreditCard they charge you extra - Crim 20:58:57 09/17/07 Hmm... - BradZ (FL) 21:00:58 09/17/07 it bugs me that they don't post prices on their website (n/m) - ZEngineer 21:56:59 09/17/07 I thought prices showed up... - BradZ (FL) 22:40:57 09/17/07 yeah when you open an account - AxleZTTic 00:16:54 09/18/07 I miss my old rims.. - Carlos Ramirez 20:17:36 09/17/07 I just coated them with a combination of wax and drool :) - ZEngineer 20:23:59 09/17/07 I thought you said the clutch came on your front clip? - collegeboy 20:42:12 09/17/07 perhaps he just bought it off a front clip engine? (n/m) - inf 20:46:37 09/17/07 Good thinking..I was confused for a second. (n/m) - collegeboy 20:48:07 09/17/07 where did I say it was MY front clip? (n/m) - ZEngineer 20:51:44 09/17/07 Got it - collegeboy 20:53:14 09/17/07 doubting is a good skill - WXY 20:55:55 09/17/07 Awsome clutch, my old 96tt parts car had that one - zboost(NoVA) 20:36:49 09/17/07 nice to know, thanks (n/m) - ZEngineer 20:52:35 09/17/07 right - aliaZ 22:15:42 09/17/07 Well he kinda makes it clear - TTFairladyZ 22:55:43 09/17/07 he didn't make it clear how bad the clutch was - aliaZ 23:20:47 09/17/07 Since he deleted his classified ad - TTFairladyZ 23:38:17 09/17/07 if that is the case - aliaZ 08:07:35 09/18/07 "A mere 100 miles...er...400 1/4 mile passes" (n/m) - collegeboy 00:04:53 09/18/07 I never heard any complaints, and measurements were - zboost(NoVA) 13:05:27 09/18/07 fair enough - aliaZ 13:44:52 09/18/07 And honestly, the clutch looked and drove the same - zboost(NoVA) 16:19:51 09/18/07 did you ever talk to RPS about it? - aliaZ 17:08:44 09/18/07 both disks should be facing forward to the engine - sparkie 21:18:45 09/17/07 thanks (n/m) - ZEngineer 21:50:35 09/17/07 that is the predecessor to the new Super Coppermix clutches - aliaZ 21:25:12 09/17/07 "I've heard it can be a bit grabby" - ZEngineer 21:51:18 09/17/07 you're lucky thats tolerated by french women (n/m) - CRAZZEPETE. 11:21:44 09/18/07 Is this the same one you were looking for replacement parts? (n/m) - Coz@CZP 00:29:10 09/18/07 yeah, that's the one. - ZEngineer 15:12:48 09/18/07
Post a Followup	You cannot reply to this message because you are not logged in.