Subject	both disks should be facing forward to the engine
Posted by	sparkie on September 17, 2007 at 9:18 PM
	This message has been viewed 113 times.
In Reply To	check out this Nismo twin plate clutch/light flywheel combo posted by ZEngineer on September 17, 2007 at 06:54 PM
Message	This way But in reality it doesn't matter because I know. I have a twin disk similar to it and I installed it both ways. The idea behind is there is one floating plate and two disk. Just make sure the two disks do not face each other so they can 'bite' into the floating plate when engaged. www.ztechz.net ICQ # 14337317
Follow Ups	check out this Nismo twin plate clutch/light flywheel combo - ZEngineer 18:54:10 09/17/07 I doubt there's anyone here is using this clutch - ZEngineer 19:08:18 09/17/07 I got the exact same one here - Russell@Z1 19:21:15 09/17/07 do you have it installed or just laying around? - ZEngineer 19:58:18 09/17/07 Just sitting - Russell@Z1 21:02:22 09/17/07 so you wouldn't know if it works with OEM throw out bearing - ZEngineer 22:16:19 09/17/07 you guys able to source the disks? - AxleZTTic 20:22:29 09/17/07 We haven't looked into it. (n/m) - Russell@Z1 21:05:21 09/17/07 I have this setup - WXY 19:28:19 09/17/07 I've read the opposite about the Z32 application - ZEngineer 20:01:51 09/17/07 same with - WXY 20:24:19 09/17/07 maybe you have an adjustment problem? (n/m) - CRAZZEPETE. 11:16:06 09/18/07 Welcome Back. (n/m) - SactoTodd 22:46:19 09/17/07 i got the same thing in my jdm engine! - AxleZTTic 20:16:18 09/17/07 You can buy them here... - BradZ (FL) 20:29:24 09/17/07 shaweeeet! thanks dood!! (n/m) - AxleZTTic 20:40:53 09/17/07 Yeah, but if you pay with a CreditCard they charge you extra - Crim 20:58:57 09/17/07 Hmm... - BradZ (FL) 21:00:58 09/17/07 it bugs me that they don't post prices on their website (n/m) - ZEngineer 21:56:59 09/17/07 I thought prices showed up... - BradZ (FL) 22:40:57 09/17/07 yeah when you open an account - AxleZTTic 00:16:54 09/18/07 I miss my old rims.. - Carlos Ramirez 20:17:36 09/17/07 I just coated them with a combination of wax and drool :) - ZEngineer 20:23:59 09/17/07 I thought you said the clutch came on your front clip? - collegeboy 20:42:12 09/17/07 perhaps he just bought it off a front clip engine? (n/m) - inf 20:46:37 09/17/07 Good thinking..I was confused for a second. (n/m) - collegeboy 20:48:07 09/17/07 where did I say it was MY front clip? (n/m) - ZEngineer 20:51:44 09/17/07 Got it - collegeboy 20:53:14 09/17/07 doubting is a good skill - WXY 20:55:55 09/17/07 Awsome clutch, my old 96tt parts car had that one - zboost(NoVA) 20:36:49 09/17/07 nice to know, thanks (n/m) - ZEngineer 20:52:35 09/17/07 right - aliaZ 22:15:42 09/17/07 Well he kinda makes it clear - TTFairladyZ 22:55:43 09/17/07 he didn't make it clear how bad the clutch was - aliaZ 23:20:47 09/17/07 Since he deleted his classified ad - TTFairladyZ 23:38:17 09/17/07 if that is the case - aliaZ 08:07:35 09/18/07 "A mere 100 miles...er...400 1/4 mile passes" (n/m) - collegeboy 00:04:53 09/18/07 I never heard any complaints, and measurements were - zboost(NoVA) 13:05:27 09/18/07 fair enough - aliaZ 13:44:52 09/18/07 And honestly, the clutch looked and drove the same - zboost(NoVA) 16:19:51 09/18/07 did you ever talk to RPS about it? - aliaZ 17:08:44 09/18/07 both disks should be facing forward to the engine - sparkie 21:18:45 09/17/07 thanks (n/m) - ZEngineer 21:50:35 09/17/07 that is the predecessor to the new Super Coppermix clutches - aliaZ 21:25:12 09/17/07 "I've heard it can be a bit grabby" - ZEngineer 21:51:18 09/17/07 you're lucky thats tolerated by french women (n/m) - CRAZZEPETE. 11:21:44 09/18/07 Is this the same one you were looking for replacement parts? (n/m) - Coz@CZP 00:29:10 09/18/07 yeah, that's the one. - ZEngineer 15:12:48 09/18/07
Post a Followup	You cannot reply to this message because you are not logged in.