Subject	Lol, and I swapped mine out after reading on here that
Posted by	550HPTT on August 09, 2007 at 8:09 PM
	This message has been viewed 30 times.
In Reply To	Why do you recommend a stock mount over nismo etc. ? (n/m) posted by 550HPTT on August 09, 2007 at 06:51 PM
Message	the stock ones were prone to "sagging" and Nismo was recommended. I do not fear what the future holds for me, I am not afraid to die.
Follow Ups	Quick question. Any noticeable gains or advantages - ShakaShaun(Denver) 17:58:40 08/09/07 My 1pc felt alot smoother than stock - TTFairladyZ 18:04:56 08/09/07 2nd... smoooooooth.. (n/m) - z_samurai 18:25:27 08/09/07 Why do you recommend a stock mount over nismo etc. ? (n/m) - 550HPTT 18:51:18 08/09/07 The Nismo trans mount isn't rated for the weight of the Z32 - YugoBernie (NoVA) 19:44:27 08/09/07 curious; any empirical evidence nismo isn't strong enough? (n/m) - BruPo 23:24:33 08/09/07 Yes - in spite of it "fitting" Nisan only lists it as a - YugoBernie (NoVA) 00:02:04 08/10/07 it doesn't look like it has half the rubber from this post. - BruPo 00:08:35 08/10/07 The amount of rubber is significantly less on the Nismo unit (n/m) - YugoBernie (NoVA) 01:11:48 08/10/07 no dis - i only ask cause my tranny is out right now - BruPo 00:18:07 08/10/07 Good for you. (n/m) - YugoBernie (NoVA) 01:12:28 08/10/07 apparently i've stumbled upon a clash of titans here.. - BruPo 11:01:12 08/10/07 pressing on the stock mount with my hand I was - mscurfield 00:33:13 08/10/07 sounds scientific to me (n/m) - Adam (NoVA) 07:32:32 08/10/07 Read this post please - TTFairladyZ 07:07:22 08/10/07 Especially Kyle's responses at the very bottom (n/m) - pallen 09:07:36 08/10/07 Lol, and I swapped mine out after reading on here that - 550HPTT 20:09:46 08/09/07 I did the UR pulley, light weight flywheel, and the - zeddiea27 20:10:06 08/09/07 Hunh? You didn't notice the rpms coming up a lot faster? - CRAZZEPETE. 07:58:29 08/10/07 Agreed...he's full of soft brownies. (n/m) - Fuzznutz 12:45:24 08/10/07 WTF? LOL! I almost spit my food out! (n/m) - zeddiea27 23:15:13 08/10/07 No, not really. I was expecting a huge difference, but - zeddiea27 23:19:19 08/10/07 Check the bracket for your shifter that bolts to the top - Zownr4life 20:29:21 08/09/07 less rotating mass ..try lifting both back to back .. the - The Devils Z 20:37:41 08/09/07 The DS has very little moment of inertia - ZCulture 23:38:56 08/09/07 ok, just ignore all the real tests and data available, not - CRAZZEPETE. 08:10:43 08/10/07 Depends on the shaft - pallen 09:11:41 08/10/07 unless your stock DS is in need of replacement - aliaZ 20:57:54 08/09/07 Thanks for the advise. I didn't think there would be any - ShakaShaun(Denver) 21:53:17 08/09/07 2nd, only consider replacing if CSB goes (n/m) - TTFairladyZ 22:28:00 08/09/07 you might have some intall probs, or balance issues - CRAZZEPETE. 08:12:24 08/10/07
Post a Followup	You cannot reply to this message because you are not logged in.