Subject	Dremel 3mm from your fenders, you and no one else will
Posted by	Scotts94z32 on July 24, 2007 at 11:42 PM
	This message has been viewed 44 times.
In Reply To	Dyno results and a PSA... posted by telegraph(Denver) on July 24, 2007 at 08:39 PM
Message	even know. SS ____________________________________________________ We face formidable challenges. I am not afraid of them. I am prepared for them.
Follow Ups	Dyno results and a PSA... - telegraph(Denver) 20:39:53 07/24/07 Re: Dyno results and a PSA... - IB 21:00:32 07/24/07 I already knew about the smoke when we tried test pipes - telegraph(Denver) 21:13:15 07/24/07 Pretty solid but it's a little lean down low for my taste - Guapo 21:02:28 07/24/07 what would you suggest doing to correct it? (n/m) - telegraph(Denver) 21:24:00 07/24/07 Easiest way is better gas or simply lower the boost. Even - Neogenesis 21:27:37 07/24/07 SAFC, or see if Tim will tune it for you. (n/m) - Guapo 22:22:55 07/24/07 91 isn't too bad at this altitude. (n/m) - 300zx90 (CO) 01:42:09 07/25/07 2nd. (n/m) - Woody75 (Denver) 08:45:46 07/25/07 People tend to forget that. (n/m) - Zluster(Abudan) 13:32:11 07/25/07 Nice curve, holds power to the end - SeedyROM 21:32:08 07/24/07 Holy...didn't see the 1.2bar at the very bottom - SeedyROM 23:57:29 07/24/07 Ya, you know, your right. - Zluster(Abudan) 00:30:52 07/25/07 Yep, much closer. (n/m) - SeedyROM 01:44:54 07/25/07 1.2 bar at Denver's altitude = ~.99bar at sea level (n/m) - Jehannum 08:52:37 07/25/07 saw the car in the lot yesterday - love the new wheels (n/m) - Tikigod (Denver) 21:57:05 07/24/07 Very nice smooth curve. - Zluster(Abudan) 22:16:23 07/24/07 1 bar on stock injectors and turbos on 91? Hell no. (n/m) - Guapo 22:23:40 07/24/07 How would you feel about 1 bar on stock inject/turbo with 93 - Zluster(Abudan) 00:12:55 07/25/07 14, maybe 15 psi tuned. (n/m) - Guapo 00:20:21 07/25/07 Thats about what I was thinking as well. - Zluster(Abudan) 00:34:59 07/25/07 1 bar doesn't leave much room for error on piss gas (n/m) - aliaZ 22:26:11 07/24/07 just the print out... good thing i got it checked - telegraph(Denver) 23:30:41 07/24/07 You might want the copy of the dyno run...... - Zluster(Abudan) 00:14:14 07/25/07 Err. - Zluster(Abudan) 00:44:00 07/25/07 umm - aliaZ 06:38:18 07/25/07 Correct 1 bar = .98 kg/cm<sup>2</sup> - Zluster(Abudan) 13:31:05 07/25/07 I know that. - aliaZ 06:28:37 07/26/07 Yup, and I was posting it for the record. (n/m) - Zluster(Abudan) 11:06:14 07/26/07 Dremel 3mm from your fenders, you and no one else will - Scotts94z32 23:42:37 07/24/07 are you serious? (n/m) - spyhunterTT(nj) 08:46:14 07/25/07 Absolutely. I was surprised at how many people I knew - Scotts94z32 09:45:25 07/25/07 I'll have an Eastwood fender roller this weekend. - Woody75 (Denver) 08:29:58 07/25/07 Did you happen to hear any "chattering" noise as it went - NAZTTy 09:22:35 07/25/07 It definitely chatters @ 3K range... what does that mean? (n/m) - telegraph(Denver) 14:43:08 07/25/07 cut the inner lining and hammer to smooth it out. - RedSER13 09:29:36 07/25/07
Post a Followup	You cannot reply to this message because you are not logged in.