Subject	fixed link
Posted by	Scotts94z32 on May 09, 2007 at 1:13 PM
	This message has been viewed 43 times.
In Reply To	poll for the issue posted by AntiHero on May 09, 2007 at 10:35 AM
Message	[ http://www.twinturbo.net/net/viewmsg.aspx?forum=polls&msg_id=4342 ] ____________________________________________________ We face formidable challenges. I am not afraid of them. I am prepared for them.
Follow Ups	Looking for definitive answers on "Built" motor mileage. - eriksu9 08:56:02 05/09/07 I would venture most guys who went with Kyle@IPP's products. - brahmabull (CT) 09:17:10 05/09/07 Well, I won't get into his products for I am not a big - eriksu9 10:10:19 05/09/07 Personally, I feel that if are running 470rwhp and keeping - Scotts94z32 10:10:39 05/09/07 It seems like very often it is not a matter of how hard - AntiHero 10:23:01 05/09/07 poll for the issue - AntiHero 10:35:28 05/09/07 fixed link - Scotts94z32 13:13:58 05/09/07 Heat the engine up with a heat gun to avoid cold starts. - Scotts94z32 10:38:28 05/09/07 Agreed. Thanks sooo much. - eriksu9 10:49:56 05/09/07 I read in DSport (I think) about Z1 building a VQ - J-Mart 11:00:32 05/09/07 Yes that is done on all motors...... (n/m) - Kyle(Houston) 11:20:13 05/09/07 I believe AliaZ is approaching 40k on his motor. (n/m) - Guapo 10:24:28 05/09/07 Excellent. It helps when you are your own engine builder - Scotts94z32 10:36:06 05/09/07 yep :) - aliaZ 10:40:01 05/09/07 *and you know wtf you're doing (n/m) - Guapo 10:44:18 05/09/07 Yea, but how many full boost cycles has he had - AZHeat 15:03:41 05/09/07 Well, he has tracked it quite often and gotten more - Guapo 15:16:23 05/09/07 I did not see that post about a built motor w/ 70k - eriksu9 10:44:42 05/09/07 It was 80k miles, and was his car: - Scotts94z32 11:30:59 05/09/07 Cool, Thx for the info. (n/m) - eriksu9 12:42:27 05/09/07 This is exaclty what keeps me awake at night. Need input: - J-Mart 10:56:41 05/09/07 First year college student? - spicyZ 11:41:26 05/09/07 Thanks for the words, but I was more concerned w/ a build. - J-Mart 13:18:44 05/09/07 Sounds like you have it all figured out. Good luck with it (n/m) - spicyZ 14:31:41 05/09/07 better young than old (n/m) - ZiNnYc 02:31:50 05/10/07 Here is my take on the whole thing - Kyle(Houston) 11:19:24 05/09/07 if you had to... - AntiHero 11:45:34 05/09/07 Moreover, What is the warranty % on average of - eriksu9 11:56:57 05/09/07 Warranty depends on the shop and not the motor - Kyle(Houston) 13:24:37 05/09/07 That's my engine Kyle refers to as getting damaged. He - bbug 00:20:57 05/10/07 are you kidding me ? 35 % ? I'd hate to have a 5 % failure - ztunerz 16:41:15 05/09/07 Yes 35%. I'm not saying that is acceptable, - eriksu9 08:04:05 05/10/07 That is very easy - Kyle(Houston) 13:13:25 05/09/07 Kyles right... - Biz(MD) 13:48:35 05/09/07 BINGO.. (n/m) - Kyle(Houston) 13:59:24 05/09/07 Well then, Why are they failing? - eriksu9 14:24:03 05/09/07 Who is "they"? - Kyle(Houston) 14:37:00 05/09/07 I am not sure what you are getting at but you asked - eriksu9 14:59:36 05/09/07 Well it all boils down to what you see - Kyle(Houston) 15:48:52 05/09/07 Rob's car runs great ... I dnk mileage but he says best - The Devils Z 18:22:42 05/09/07 Big 2nd. After the inital problems were found and fixed, - eriksu9 08:18:07 05/10/07 i think everyone should build their own motors >> - ztunerz 16:35:25 05/09/07 Harry ..that was funny .. .lol (n/m) - The Devils Z 18:23:19 05/09/07 i say check your rod bearings once a year - no problem :) (n/m) - ztunerz 16:32:43 05/09/07 Ash said the same thing to me a few years ago .. (n/m) - The Devils Z 18:23:58 05/09/07 built many motors with forged internals - ztunerz 16:30:18 05/09/07 Harry, what are your piston to wall clearance with the - AZHeat 16:40:37 05/09/07 i use exactly what wiesco suggests and adjust if NOS is - ztunerz 16:43:26 05/09/07 Awesome! Thats what I am looking for.... - eriksu9 08:21:48 05/10/07 Me. :-) 2+ years with no issues on Kyle's built motor. - 1BADTTZ (SoCal) 17:06:01 05/09/07
Post a Followup	You cannot reply to this message because you are not logged in.