Subject	I'm not Ash, but I know that there's no "surely"
Posted by	ZEngineer on May 04, 2007 at 2:59 PM
	This message has been viewed 43 times.
In Reply To	thank you Ash, so if i buy a new cranckshaft from nissan, posted by bubuche on May 04, 2007 at 02:51 PM
Message	when it comes to bearing selection. You have to measure your clearance and match the correct parts. _________________________________________________________________________________ Im n0t Sarcastic (Kenny): not to over do it, but you're certainly the source of high-class Z mods ZEngineer24: what do you mean by that? Im n0t Sarcastic: I just mean, your Z is one I really admire "The Z is the cause and the solution to all my problems" -- Me "If your car was my car, I'd think it's broken"
Follow Ups	300zx drift machine, bearing gone, why???????? - bubuche 13:54:52 05/04/07 Oil starvation, detonation, etc. (n/m) - Kenny 14:04:23 05/04/07 you say that you built the engine yourself - ZEngineer 14:07:15 05/04/07 Take pictures and post. How many miles on it? - AZHeat 14:10:05 05/04/07 I did 50 miles and then i changed the oil. - bubuche 14:21:16 05/04/07 how much boost were you running? - aliaZ 14:27:41 05/04/07 running about 12 psi and didn't check bearing clearance :( (n/m) - bubuche 14:52:18 05/04/07 Thats not good (n/m) - Slow3z 15:07:05 05/04/07 oops - aliaZ 15:43:47 05/04/07 When using aftermarket bearings you must size the big - Ash's Z 14:30:31 05/04/07 thank you Ash, so if i buy a new cranckshaft from nissan, - bubuche 14:51:44 05/04/07 I'm not Ash, but I know that there's no "surely" - ZEngineer 14:59:13 05/04/07 No, you wont be able to do that. What you have to do is - Ash's Z 15:17:10 05/04/07 In addition to this process, I strongly recommend that you - Ash's Z 15:25:38 05/04/07 Re: In addition to this process, I strongly recommend that y - Kenny 15:32:04 05/04/07 You'll find that a vast majority of machine shops that build - Ash's Z 16:05:50 05/04/07 Thank you. (n/m) - Kenny 16:09:43 05/04/07 12psi won't beat an RS4. Stop street racing... - OrlandoTT 15:40:22 05/04/07 12psi on a built 700BB motor might - BigTDogg (MA) 15:45:11 05/04/07 I didn't see that anywhere in his profile... - OrlandoTT 15:53:50 05/04/07 Location: Dijon, FR France (n/m) - Barry'z (NJ) 16:29:10 05/04/07 Not location... 700BB turbos. (n/m) - OrlandoTT 20:15:35 05/04/07 My Bad. (n/m) - Barry'z (NJ) 21:14:18 05/04/07 Define brutal and which generation of RS4 (n/m) - BigTDogg (MA) 17:45:17 05/04/07 Mid 4 seconds to 60 with AWD stock. Current gen. (n/m) - OrlandoTT 20:17:17 05/04/07 At 12psi I put down 468rwhp. I raced a RS4 - Octavian 16:38:11 05/04/07 lol yes i'm french so i do my best ;) - bubuche 17:52:43 05/04/07 Wow sounds like a nice setup! Hope you get the bearing - TyreeZtt (SeKy) 18:03:29 05/04/07 Sounds like those RS4s are Z killers. ;) (n/m) - SactoTodd 19:41:29 05/04/07 Wow! That's a lot for 12psi with any turbos... - OrlandoTT 20:19:31 05/04/07 What oil are you running? (n/m) - Ash's Z 19:57:41 05/04/07 Changed from 10w40 semi synthetic for break in to - bubuche 10:46:25 05/05/07 I would recommend you to run 10W-30 lube. Nissan did - Ash's Z 20:31:39 05/05/07 I hate you! Two words... Melissa Theuriau. - PiotrC70 20:04:25 05/04/07 oops... forgot the link. - PiotrC70 00:34:04 05/05/07 They should make her the next Vitorias Secret model! WOW (n/m) - MidLifeZ (DFW) 08:42:43 05/05/07 SAY IT! The first link I found for her video - PiotrC70 18:33:53 05/05/07
Post a Followup	You cannot reply to this message because you are not logged in.