Subject	it is very easy, its on top of the plenum. like 2 10mm bolts
Posted by	NobleZ on April 13, 2007 at 2:06 PM
	This message has been viewed 20 times.
In Reply To	Re: 50 psi is a bit low for full throttle posted by Zenica on April 13, 2007 at 02:02 PM
Message	and two hose clamps. i would try the 6 p's before sending the ecu back. u must like girls with tits and no ass too (n/m) - ARA300ZX 12:07:22 03/27/07 Personally, I like my Z's ghetto booty - Slow3z 12:09:07 03/27/07 Nuthin' says tru love like a gat. (n/m) - YugoBernie (NoVA) 02/10/07 01:01:19 (1) Looks like a quality movie. (n/m) - Brian Spilner 02/07/07 LOL, sweet sig name. (n/m) - jmw23712 02/07/07 22:53:10 yeah, typical white-boy name - ZEngineer 02/08/07 08:52:09 in other news. thousands of people did not receive their holiday mail.... sources close the USPS said that they believe an interweb site page is responsible for the sabotage that has left its tell tale calling cards jamming their machines... a spokes person for the interpage in question is quoted as replying to the aleagtions with the following responese. "false" - dvlhntr 12/12/06 22:35:35
Follow Ups	My Z is sick. - Zenica 13:53:55 04/13/07 50 psi is a bit low for full throttle - spyhunterTT(nj) 13:59:16 04/13/07 Re: 50 psi is a bit low for full throttle - Zenica 14:02:41 04/13/07 it is very easy, its on top of the plenum. like 2 10mm bolts - NobleZ 14:06:27 04/13/07 Your fuel pressure should be 43.5, at zero manifold - octavian-z 14:04:21 04/13/07 I forgot, also check your FPR (n/m) - octavian-z 14:06:34 04/13/07 correct, but will dip below that at idle, since - Guapo 14:09:28 04/13/07 Thanks for the replies.. - Zenica 14:12:47 04/13/07 RE: Idle psi - Broke_as_**** 14:19:24 04/13/07 It's an erratic jump because the fuel pump controller - octavian-z 14:26:21 04/13/07 With your mods, you should be around 375 rwhp. - eriksu9 14:25:04 04/13/07 Re: With your mods, you should be around 375 rwhp. - Zenica 14:32:47 04/13/07 that doesn't sound too far off - spyhunterTT(nj) 14:38:33 04/13/07 Re: that doesn't sound too far off - Zenica 14:41:48 04/13/07 A vacuum leak would cause him to run rich, not lean. (n/m) - Billteed1 15:00:52 04/13/07 I should have said a boost leak. - Billteed1 15:27:16 04/13/07 I would check for a vacuum leak after checking the FPR - olyar15 14:29:29 04/13/07 How would they let in unmetered air - Billteed1 15:02:38 04/13/07 Not on the inlet side - Broke_as_**** 15:07:42 04/13/07 Re: Not on the inlet side - Zenica 15:17:04 04/13/07 Carb sprary is good for find a leak... - Broke_as_**** 15:51:36 04/13/07 Re: Carb sprary is good for find a leak... - Zenica 16:00:27 04/13/07 I see - Billteed1 15:25:28 04/13/07
Post a Followup	You cannot reply to this message because you are not logged in.