Subject	Just finished the 120k service - how long should I wait for
Posted by	Poppe on March 25, 2007 at 2:25 PM
	This message has been viewed 134 times.
Message	permatex rtv sealant to cure? I want to take it out for a test drive before I have to go to work tomorrow, but don't want to subject the rtv sealant on the hard water pipes to pressure if it isn't set. So - its been about 4 hours since I put those pipes back in. Long enough or keep waiting?
Follow Ups	Just finished the 120k service - how long should I wait for - Poppe 14:25:42 03/25/07 it might say on the tube (n/m) - turbomaniac 14:30:45 03/25/07 It says 24 hours for full cure; don't want to wait that long (n/m) - Poppe 14:31:59 03/25/07 After that amount of work, 24 hours is a cheap price to - Audioquest 15:56:15 03/25/07 Then why ask the question? (n/m) - OrlandoTT 16:36:47 03/25/07 Re: Just finished the 120k service - how long should I wait for - awesom-o 14:53:17 03/25/07 Re: Just finished the 120k service - how long should I wait for - Tuppidsay 15:01:34 03/25/07 2nd. the time it takes to re assemble is time enough - nemo1080 10:19:21 03/26/07 Yyou must be cutting a lot of corners if you can do a - Guapo 11:20:34 03/26/07 Or parts... probably a few very important ones at that... (n/m) - Kaz (Dallas) 11:21:37 03/26/07 LoL. (n/m) - YugoBernie (NoVA) 12:06:28 03/26/07 2 hours?? - TT XTZ 14:16:49 03/26/07 Tear apart, toss on belt, cobble together. Pray. (n/m) - YugoBernie (NoVA) 17:14:51 03/26/07 lol@ pray part (n/m) - Waco300zx 23:38:23 03/26/07 I have never had a leak putting it together and - spddracer 16:11:20 03/25/07 I waited 20 min and it was fine however I would wait - dream Z (MD) 17:19:40 03/25/07 Alright, I'll wait like 10 hours. Not getting antsy - ok, - Poppe 17:42:41 03/25/07 I just did my timing belt a week ago - lakerdude42 20:10:42 03/25/07 permatex RTV is crap Nissan liquid gasket is ready in 30 min (n/m) - Fast300 20:38:19 03/25/07 I've never had an issue using Permatex. - Woody75 (Denver) 23:16:42 03/25/07 And Genuine Nissan 999MP-A7007P will work for both (n/m) - Fast300 23:24:48 03/25/07 Nothing like paying $19 a tube for something you can by for - YugoBernie (NoVA) 01:17:46 03/26/07 Permatex is poor compared to GE and Dow Corning... (n/m) - CaliguyPurdue (redesigning) 10:37:03 03/26/07 How so? (n/m) - YugoBernie (NoVA) 12:18:01 03/26/07 Quality control issues... insufficient mixing - CaliguyPurdue (redesigning) 12:44:22 03/26/07 who makes the Nissan branded product? (n/m) - Guapo 12:11:05 03/26/07 Waited about 10 hours before burping the radiator and taking - Poppe 06:57:50 03/26/07
Post a Followup	You cannot reply to this message because you are not logged in.