Subject	The reason they want "US" to supply the dimensions
Posted by	eriksu9 on January 09, 2007 at 7:26 AM
	This message has been viewed 46 times.
In Reply To	Spoke to Richmond Gears today at length ..need help posted by The Devils Z on January 08, 2007 at 11:48 AM
Message	and NOT the transmission itself is pretty common. If you send in the drawings and they make the tranny to those exact specs from "YOUR" drawings, If there is an issue with being wrong, the problem is from the specs you gave them therefore, it is your fault and there is no way they can be held responsible because you supplied them with wrong specs. Now, If they get the tranny, drawup its dimensions and spec it out, spend hours upon hours manufacturing the unit, build 100 transmissions, and they are 1mm off and the units are deemed unusable, the problem is on "THEM" and they will have to eat it. Nowadays, a lot of tech depts want you to supply exact measurements and they will make it to your specs. It allows for less chance of error as opposed to them getting the tranny, taking measurements, being 1mm off and then eating the costs...Just FYI. ****472 RWHP/461 TORQUE ON 110 RACE GAS @21 PSI ****438 RWHP ON 93 OCTANE PUMP GAS/STOCK MOTOR**** ****429 FT LBS/TQ*******************************
Follow Ups	Spoke to Richmond Gears today at length ..need help - The Devils Z 11:48:18 01/08/07 What kind of "mold" are they talking about?? - CaliguyPurdue (redesigning) 12:21:17 01/08/07 Yes - they would supply an entire new transmission - The Devils Z 12:40:10 01/08/07 So they would then need the following... - CaliguyPurdue (redesigning) 12:47:52 01/08/07 Ahem... - RSR 13:17:46 01/08/07 I'm confused. (imagine that). - ni[X]it 19:33:41 01/08/07 Learn to reply to the right post douche! (n/m) - nixit 20:07:16 01/08/07 Hehe, this whole topic is getting confused. - RSR 07:54:53 01/09/07 external dimensions ... and nevermind (n/m) - The Devils Z 20:07:47 01/08/07 I can do it. It'll just take some time. Not overnight. - nixit 20:09:34 01/08/07 from talking with Jim -- I didn't realize how much an - The Devils Z 21:03:59 01/08/07 below is what they are looking for to get started !!!! - The Devils Z 21:33:10 01/08/07 Thats do-able... (n/m) - CaliguyPurdue (redesigning) 23:09:25 01/08/07 Rather then playing lost in translation... it might be best - YugoBernie (NoVA) 12:45:05 01/08/07 for clarity sake --I need a dimensional drawing ..not - The Devils Z 12:40:58 01/08/07 It would be nice if you could confirm we still get to use - zboost(NoVA) 12:50:43 01/08/07 why not just get the 98+ JDM trannies - i_drive 13:13:55 01/08/07 From Dee's profile 'New Nissan 97+ JDM transmission' - EricTTZ 14:55:56 01/08/07 The 97+ OEM tranny is not "bulletproof". Its just bett-ER. - Inzane 22:46:10 01/08/07 that sounds very expensive. Why not adapt a - AzHeat 13:57:32 01/08/07 for clarity sake - I need a dimensional stock drawing - The Devils Z 14:25:52 01/08/07 I can't help you there, but keep us all updated (n/m) - TexanZX 14:37:38 01/08/07 talk 2 g-force.. they might be able to do stronger internals - Z32POWER.com 15:15:51 01/08/07 All of thats overkill for a street Z IMO - kryptonite729@VP 15:28:23 01/08/07 thats what i was saying about G-Force - Z32POWER.com 06:20:36 01/09/07 How is the red car running? What kind of times - RSR 08:01:38 01/09/07 car is put on backburner for a few months - Z32POWER.com 14:31:14 01/09/07 That is a completely unreasonable amount of overkill - RSR 18:24:55 01/08/07 absolutely - Z32POWER.com 06:23:07 01/09/07 Huh? - RSR 08:00:53 01/09/07 i agree with ya man - Z32POWER.com 14:30:01 01/09/07 They talk about up front costs? - SeedyROM 15:18:37 01/08/07 My thoughts exactly (n/m) - Toso 19:26:10 01/08/07 it won't be 100k if they can use an existing bellhousing - The Devils Z 20:08:43 01/08/07 The stock bell housing doesn't bolt on/off, does it? - nixit 20:10:58 01/08/07 auto bell housing is removable. (n/m) - zboost(NoVA) 20:41:11 01/08/07 If you look at the link below (in case that you missed it ) - The Devils Z 21:06:34 01/08/07 Still a chunk of change and a big "if". - SeedyROM 02:53:06 01/09/07 I want to give you kudos for correctly spelling - RSR 10:05:47 01/09/07 Do you think high torque killed the stock tranny and not - AzHeat 16:12:41 01/08/07 My tranny has 20K on it ... and I didn't sloppy shift - The Devils Z 20:11:40 01/08/07 The reason they want "US" to supply the dimensions - eriksu9 07:26:26 01/09/07
Post a Followup	You cannot reply to this message because you are not logged in.