Subject	All of thats overkill for a street Z IMO
Posted by	kryptonite729@VP on January 08, 2007 at 3:28 PM
	This message has been viewed 57 times.
In Reply To	talk 2 g-force.. they might be able to do stronger internals posted by Z32POWER.com on January 08, 2007 at 03:15 PM
Message	The G-force is a race tranny and will require rebuilds far more than 99.9% of the Z enthusiast will want to do. The Toyota 6spd is a bad candidate due to the rear drive ratio of the 300zx is setup for a 5spd tranny, switching to a 6spd will kill the final drive ratio to the tranny if that makes sense. 1st gear on the 6spd supra tranny will be useless with the 3.69ish ratio of the manual Z. You would have to swap to like a 3.13 or 3.23 final drive for the Supra tranny to work properly IMO. Can Richmond not just take the gears out of the tranny and mold the GEARS and bearings out of stronger material? Maybe i'm missing the concept though as i'm somewhat out of the loop of the manuals now that i got a auto Z :(
Follow Ups	Spoke to Richmond Gears today at length ..need help - The Devils Z 11:48:18 01/08/07 What kind of "mold" are they talking about?? - CaliguyPurdue (redesigning) 12:21:17 01/08/07 Yes - they would supply an entire new transmission - The Devils Z 12:40:10 01/08/07 So they would then need the following... - CaliguyPurdue (redesigning) 12:47:52 01/08/07 Ahem... - RSR 13:17:46 01/08/07 I'm confused. (imagine that). - ni[X]it 19:33:41 01/08/07 Learn to reply to the right post douche! (n/m) - nixit 20:07:16 01/08/07 Hehe, this whole topic is getting confused. - RSR 07:54:53 01/09/07 external dimensions ... and nevermind (n/m) - The Devils Z 20:07:47 01/08/07 I can do it. It'll just take some time. Not overnight. - nixit 20:09:34 01/08/07 from talking with Jim -- I didn't realize how much an - The Devils Z 21:03:59 01/08/07 below is what they are looking for to get started !!!! - The Devils Z 21:33:10 01/08/07 Thats do-able... (n/m) - CaliguyPurdue (redesigning) 23:09:25 01/08/07 Rather then playing lost in translation... it might be best - YugoBernie (NoVA) 12:45:05 01/08/07 for clarity sake --I need a dimensional drawing ..not - The Devils Z 12:40:58 01/08/07 It would be nice if you could confirm we still get to use - zboost(NoVA) 12:50:43 01/08/07 why not just get the 98+ JDM trannies - i_drive 13:13:55 01/08/07 From Dee's profile 'New Nissan 97+ JDM transmission' - EricTTZ 14:55:56 01/08/07 The 97+ OEM tranny is not "bulletproof". Its just bett-ER. - Inzane 22:46:10 01/08/07 that sounds very expensive. Why not adapt a - AzHeat 13:57:32 01/08/07 for clarity sake - I need a dimensional stock drawing - The Devils Z 14:25:52 01/08/07 I can't help you there, but keep us all updated (n/m) - TexanZX 14:37:38 01/08/07 talk 2 g-force.. they might be able to do stronger internals - Z32POWER.com 15:15:51 01/08/07 All of thats overkill for a street Z IMO - kryptonite729@VP 15:28:23 01/08/07 thats what i was saying about G-Force - Z32POWER.com 06:20:36 01/09/07 How is the red car running? What kind of times - RSR 08:01:38 01/09/07 car is put on backburner for a few months - Z32POWER.com 14:31:14 01/09/07 That is a completely unreasonable amount of overkill - RSR 18:24:55 01/08/07 absolutely - Z32POWER.com 06:23:07 01/09/07 Huh? - RSR 08:00:53 01/09/07 i agree with ya man - Z32POWER.com 14:30:01 01/09/07 They talk about up front costs? - SeedyROM 15:18:37 01/08/07 My thoughts exactly (n/m) - Toso 19:26:10 01/08/07 it won't be 100k if they can use an existing bellhousing - The Devils Z 20:08:43 01/08/07 The stock bell housing doesn't bolt on/off, does it? - nixit 20:10:58 01/08/07 auto bell housing is removable. (n/m) - zboost(NoVA) 20:41:11 01/08/07 If you look at the link below (in case that you missed it ) - The Devils Z 21:06:34 01/08/07 Still a chunk of change and a big "if". - SeedyROM 02:53:06 01/09/07 I want to give you kudos for correctly spelling - RSR 10:05:47 01/09/07 Do you think high torque killed the stock tranny and not - AzHeat 16:12:41 01/08/07 My tranny has 20K on it ... and I didn't sloppy shift - The Devils Z 20:11:40 01/08/07 The reason they want "US" to supply the dimensions - eriksu9 07:26:26 01/09/07
Post a Followup	You cannot reply to this message because you are not logged in.