TwinTurbo.NET: Nissan 300ZX forum - *decreases density... (n/m)
Subject
*decreases density... (n/m)
Posted by
CaliguyPurdue
on December 29, 2006 at 3:53 PM
This message has been viewed
34
times.
In Reply To
I think the idea of making a substance harder without making
posted by Ash's Z
on December 29, 2006 at 03:23 PM
Message
Follow Ups
Potential Transmission Issue for HIGH RWHP Zs ???
-
The Devils Z
00:27:39 12/29/06
I have that same exact sound.
-
WAGGZ
00:36:17 12/29/06
It only makes sound when the clutch is *engaged* (n/m)
-
WAGGZ
00:37:34 12/29/06
mine did the same thing, but i just put in a new, used,..
-
octavian-z
00:44:08 12/29/06
right
-
WAGGZ
00:47:04 12/29/06
I broke my tranny two days after getting it tunned
-
octavian-z
00:38:23 12/29/06
Supra OEM 6spd supports 1500hp without treating
-
kryptonite729@VP
01:24:02 12/29/06
Thats if you find a Supra with a 6spd, its funny that almost
-
Eishozzzz
02:23:38 12/29/06
I wish that we had a trans that durable... (n/m)
-
Kong ZTT GT28RS MD
12:26:29 12/29/06
Could be worse! We could be driving Subarus!
-
CaliguyPurdue
12:45:27 12/29/06
LOL! (n/m)
-
Ash's Z
15:30:28 12/29/06
How was the trans broken in, and what oil did you use? (n/m)
-
ENVYMYZ
00:47:27 12/29/06
Cryo-treating after it's already fubar'd is putting the cart
-
Kenny
01:03:47 12/29/06
Cryo-treat the replacement bearings.
-
Ash's Z
02:25:56 12/29/06
Ash, i dont think cryo treating changes the dimension's
-
Eishozzzz
02:36:38 12/29/06
You are correct in the sense that martensite is lower
-
CaliguyPurdue
03:01:54 12/29/06
I think the idea of making a substance harder without making
-
Ash's Z
15:23:43 12/29/06
Why are you explaining that to Jim? (n/m)
-
Kenny
15:42:00 12/29/06
Wasn't really - just bouncing the ideas off of someone
-
Ash's Z
16:42:53 12/29/06
*decreases density... (n/m) -
CaliguyPurdue
15:53:52 12/29/06
In an ideal world, cost wouldn't be an issue :)
-
CaliguyPurdue
16:06:34 12/29/06
Interesting you bring that up. I attended a lecture a few
-
Ash's Z
16:49:03 12/29/06
Well I'll take that as a huge compliment...
-
CaliguyPurdue
18:33:45 12/29/06
cryo treating DOES change dimensions, but barely
-
jkeyser14
15:35:38 12/29/06
Replacing any of the bearings in our trannies is a very
-
Ash's Z
02:21:54 12/29/06
And I might add the fact that to remove the input shaft,
-
Ash's Z
02:33:21 12/29/06
solution>>>>>>>>>>>>>
-
Antonio(AZ)
08:16:28 12/29/06
Tranny and diff coolers for hi HP Zs is a great idea. (n/m)
-
BigTDogg (MA)
08:42:48 12/29/06
this would be a nice mod. I'd buy it if it was available
-
The Devils Z
09:38:02 12/29/06
european Z32 MT gearboxes have oil cooling in stock form
-
lymon
12:10:04 12/29/06
Yes please do! If folks wanted to do this OEM would be
-
CaliguyPurdue
12:40:19 12/29/06
Agreed (n/m)
-
The Devils Z
13:09:52 12/29/06
If I remember correctly...
-
NobleZ
10:06:12 12/29/06
You sure he wasn't talking about an auto tranny?
-
RSR
10:15:08 12/29/06
Pilot bushing/needle bearing :)
-
BigTDogg (MA)
08:44:21 12/29/06
yeah --- replacing that as well. I physically didn't tear
-
The Devils Z
09:36:59 12/29/06
Throwout bearing.
-
eriksu9
09:44:19 12/29/06
2nd that! (n/m)
-
MULTI-Z
11:25:38 12/29/06
What Dee is describing is the input shaft bearing.
-
Only1Z
11:54:45 12/29/06
Post a
Followup
You cannot reply to this message because you are not
logged in
.