TwinTurbo.NET: Nissan 300ZX forum - Agreed (n/m)
Subject
Agreed (n/m)
Posted by
The Devils Z
on December 29, 2006 at 1:09 PM
This message has been viewed
22
times.
In Reply To
Yes please do! If folks wanted to do this OEM would be
posted by CaliguyPurdue
on December 29, 2006 at 12:40 PM
Message
Follow Ups
Potential Transmission Issue for HIGH RWHP Zs ???
-
The Devils Z
00:27:39 12/29/06
I have that same exact sound.
-
WAGGZ
00:36:17 12/29/06
It only makes sound when the clutch is *engaged* (n/m)
-
WAGGZ
00:37:34 12/29/06
mine did the same thing, but i just put in a new, used,..
-
octavian-z
00:44:08 12/29/06
right
-
WAGGZ
00:47:04 12/29/06
I broke my tranny two days after getting it tunned
-
octavian-z
00:38:23 12/29/06
Supra OEM 6spd supports 1500hp without treating
-
kryptonite729@VP
01:24:02 12/29/06
Thats if you find a Supra with a 6spd, its funny that almost
-
Eishozzzz
02:23:38 12/29/06
I wish that we had a trans that durable... (n/m)
-
Kong ZTT GT28RS MD
12:26:29 12/29/06
Could be worse! We could be driving Subarus!
-
CaliguyPurdue
12:45:27 12/29/06
LOL! (n/m)
-
Ash's Z
15:30:28 12/29/06
How was the trans broken in, and what oil did you use? (n/m)
-
ENVYMYZ
00:47:27 12/29/06
Cryo-treating after it's already fubar'd is putting the cart
-
Kenny
01:03:47 12/29/06
Cryo-treat the replacement bearings.
-
Ash's Z
02:25:56 12/29/06
Ash, i dont think cryo treating changes the dimension's
-
Eishozzzz
02:36:38 12/29/06
You are correct in the sense that martensite is lower
-
CaliguyPurdue
03:01:54 12/29/06
I think the idea of making a substance harder without making
-
Ash's Z
15:23:43 12/29/06
Why are you explaining that to Jim? (n/m)
-
Kenny
15:42:00 12/29/06
Wasn't really - just bouncing the ideas off of someone
-
Ash's Z
16:42:53 12/29/06
*decreases density... (n/m)
-
CaliguyPurdue
15:53:52 12/29/06
In an ideal world, cost wouldn't be an issue :)
-
CaliguyPurdue
16:06:34 12/29/06
Interesting you bring that up. I attended a lecture a few
-
Ash's Z
16:49:03 12/29/06
Well I'll take that as a huge compliment...
-
CaliguyPurdue
18:33:45 12/29/06
cryo treating DOES change dimensions, but barely
-
jkeyser14
15:35:38 12/29/06
Replacing any of the bearings in our trannies is a very
-
Ash's Z
02:21:54 12/29/06
And I might add the fact that to remove the input shaft,
-
Ash's Z
02:33:21 12/29/06
solution>>>>>>>>>>>>>
-
Antonio(AZ)
08:16:28 12/29/06
Tranny and diff coolers for hi HP Zs is a great idea. (n/m)
-
BigTDogg (MA)
08:42:48 12/29/06
this would be a nice mod. I'd buy it if it was available
-
The Devils Z
09:38:02 12/29/06
european Z32 MT gearboxes have oil cooling in stock form
-
lymon
12:10:04 12/29/06
Yes please do! If folks wanted to do this OEM would be
-
CaliguyPurdue
12:40:19 12/29/06
Agreed (n/m) -
The Devils Z
13:09:52 12/29/06
If I remember correctly...
-
NobleZ
10:06:12 12/29/06
You sure he wasn't talking about an auto tranny?
-
RSR
10:15:08 12/29/06
Pilot bushing/needle bearing :)
-
BigTDogg (MA)
08:44:21 12/29/06
yeah --- replacing that as well. I physically didn't tear
-
The Devils Z
09:36:59 12/29/06
Throwout bearing.
-
eriksu9
09:44:19 12/29/06
2nd that! (n/m)
-
MULTI-Z
11:25:38 12/29/06
What Dee is describing is the input shaft bearing.
-
Only1Z
11:54:45 12/29/06
Post a
Followup
You cannot reply to this message because you are not
logged in
.