Subject	Ash, i dont think cryo treating changes the dimension's
Posted by	Eishozzzz on December 29, 2006 at 2:36 AM
	This message has been viewed 48 times.
In Reply To	Cryo-treat the replacement bearings. posted by Ash's Z on December 29, 2006 at 02:25 AM
Message	of the materials, but i could be wrong. From what ive read, people are using cryo in Nascar Eng parts now, and some of the parts that they treat dont need to be replaced for two races. I also sent out my output shafts to [ www.cryoscience.com ] and ill give them a call morrow, just to make sure about the change of the dimensions.
Follow Ups	Potential Transmission Issue for HIGH RWHP Zs ??? - The Devils Z 00:27:39 12/29/06 I have that same exact sound. - WAGGZ 00:36:17 12/29/06 It only makes sound when the clutch is *engaged* (n/m) - WAGGZ 00:37:34 12/29/06 mine did the same thing, but i just put in a new, used,.. - octavian-z 00:44:08 12/29/06 right - WAGGZ 00:47:04 12/29/06 I broke my tranny two days after getting it tunned - octavian-z 00:38:23 12/29/06 Supra OEM 6spd supports 1500hp without treating - kryptonite729@VP 01:24:02 12/29/06 Thats if you find a Supra with a 6spd, its funny that almost - Eishozzzz 02:23:38 12/29/06 I wish that we had a trans that durable... (n/m) - Kong ZTT GT28RS MD 12:26:29 12/29/06 Could be worse! We could be driving Subarus! - CaliguyPurdue 12:45:27 12/29/06 LOL! (n/m) - Ash's Z 15:30:28 12/29/06 How was the trans broken in, and what oil did you use? (n/m) - ENVYMYZ 00:47:27 12/29/06 Cryo-treating after it's already fubar'd is putting the cart - Kenny 01:03:47 12/29/06 Cryo-treat the replacement bearings. - Ash's Z 02:25:56 12/29/06 Ash, i dont think cryo treating changes the dimension's - Eishozzzz 02:36:38 12/29/06 You are correct in the sense that martensite is lower - CaliguyPurdue 03:01:54 12/29/06 I think the idea of making a substance harder without making - Ash's Z 15:23:43 12/29/06 Why are you explaining that to Jim? (n/m) - Kenny 15:42:00 12/29/06 Wasn't really - just bouncing the ideas off of someone - Ash's Z 16:42:53 12/29/06 *decreases density... (n/m) - CaliguyPurdue 15:53:52 12/29/06 In an ideal world, cost wouldn't be an issue :) - CaliguyPurdue 16:06:34 12/29/06 Interesting you bring that up. I attended a lecture a few - Ash's Z 16:49:03 12/29/06 Well I'll take that as a huge compliment... - CaliguyPurdue 18:33:45 12/29/06 cryo treating DOES change dimensions, but barely - jkeyser14 15:35:38 12/29/06 Replacing any of the bearings in our trannies is a very - Ash's Z 02:21:54 12/29/06 And I might add the fact that to remove the input shaft, - Ash's Z 02:33:21 12/29/06 solution>>>>>>>>>>>>> - Antonio(AZ) 08:16:28 12/29/06 Tranny and diff coolers for hi HP Zs is a great idea. (n/m) - BigTDogg (MA) 08:42:48 12/29/06 this would be a nice mod. I'd buy it if it was available - The Devils Z 09:38:02 12/29/06 european Z32 MT gearboxes have oil cooling in stock form - lymon 12:10:04 12/29/06 Yes please do! If folks wanted to do this OEM would be - CaliguyPurdue 12:40:19 12/29/06 Agreed (n/m) - The Devils Z 13:09:52 12/29/06 If I remember correctly... - NobleZ 10:06:12 12/29/06 You sure he wasn't talking about an auto tranny? - RSR 10:15:08 12/29/06 Pilot bushing/needle bearing :) - BigTDogg (MA) 08:44:21 12/29/06 yeah --- replacing that as well. I physically didn't tear - The Devils Z 09:36:59 12/29/06 Throwout bearing. - eriksu9 09:44:19 12/29/06 2nd that! (n/m) - MULTI-Z 11:25:38 12/29/06 What Dee is describing is the input shaft bearing. - Only1Z 11:54:45 12/29/06
Post a Followup	You cannot reply to this message because you are not logged in.