Subject	whoa!
Posted by	Dallas DamonZ on December 28, 2006 at 8:39 AM
	This message has been viewed 54 times.
In Reply To	Yes you are right, I made a mistake when I set them posted by Booster (MD) on December 27, 2006 at 07:18 PM
Message	:that low I did not know you could run 14 or 15 even 16psi on pump gas, I haven't read the whole thread, so I might have missed a detail in here... Be careful! Your 15PSI is different from most everyone else's 15PSI here. With all the work on the car (turbos/heads/valves/etc) it flows a lot better then stage IIIs. Your 10PSI might be pretty close to the rest of our world's higher numbers. The engine is a simple air pump and your through volume is a lot higher then most of us resulting in lower PSI for the same power output (obviously). I'd suggest leaving the WGs where they are at until you find out where pump gas starts to fail (detonate) on the dyno, then set your wastegates a couple PSI below that for overhead. Then see where your max ends up at. Later "If A equals success, then the formula is: A = X + Y + Z, X is work. Y is play. Z is keep your mouth shut." - Albert Einstein When was the last time you *really* did something with your Z to call yourself a Z enthusiast? Member #1 PETZ
Follow Ups	I went to the dyno today 477.9RWHP @ 397.1 ft/lbs - Booster (MD) 17:45:36 12/27/06 Very nice! (n/m) - turtleboy 17:50:25 12/27/06 Nice # for pump gas! What boost level did you run - natottz 18:02:53 12/27/06 "at 10psi" (n/m) - zxtuner161 18:09:43 12/27/06 I see upper 500's in the near future! (n/m) - Spongerider :) 18:04:34 12/27/06 477.9RWHP @ 397.1 ft/lbs at 10psi?!? how the hell?????? (n/m) - delox 18:27:51 12/27/06 looks like it is flywheel hp (n/m) - ashman2k2 18:33:01 12/27/06 It is RWHP, I do not know why it says flywheel graph - Booster (MD) 18:48:32 12/27/06 sexy JDM type-USA tails! (n/m) - redfarsi 00:47:16 12/28/06 Refers to the dyno flywheel (n/m) - Joe(NoVA) 18:51:46 12/27/06 nice. you sure it was 10 psi? - aliaZ 18:52:52 12/27/06 He said my AF ratio what not in spec so he did not - Booster (MD) 19:02:51 12/27/06 if your wastegates are set to 13psi - aliaZ 19:08:52 12/27/06 Yes you are right, I made a mistake when I set them - Booster (MD) 19:18:43 12/27/06 if you're making that much power at 10psi - moxie (SF) 20:51:21 12/27/06 Good point (n/m) - Booster (MD) 20:58:35 12/27/06 agreed (n/m) - aliaZ 21:19:22 12/27/06 whoa! - Dallas DamonZ 08:39:05 12/28/06 I was told by Ben at JWT that with my ECU - Booster (MD) 12:33:14 12/28/06 your injectors are not the limiting factor here - aliaZ 12:42:06 12/28/06 2nd - Dallas DamonZ 19:03:50 12/28/06 3rd - ztunerz 21:36:50 12/28/06 No he did not give it to me, I just stopped - Booster (MD) 21:48:59 12/28/06 They don't. Their base boost is set for 12 psi. (n/m) - Riddick (looks clear) 12:43:54 12/28/06 unless the actuators are adjusted otherwise - aliaZ 22:48:44 12/28/06 200 whp @ 4krpm?? - Pacmanpth 19:30:19 12/27/06 not really - looks very much like numbers i have seen with - ztunerz 22:39:57 12/27/06 10psi, i know ppl with 700s put down that HP at 12psi, - Eishozzzz 19:51:02 12/27/06 yeah, it is... says it right on the dyno (n/m) - moxie (SF) 21:41:48 12/27/06 IIRC, Dynapacks rate power at the flywheel of the dyno, - Guapo 21:43:32 12/27/06 ahh.. cool. thanks, didn't know that (n/m) - moxie (SF) 22:13:45 12/27/06 nice ! (n/m) - The Devils Z 21:01:18 12/27/06 Nice numbers. (n/m) - Piranha(Omaha) 23:54:18 12/27/06 Impressive numbers for 10psi. - sfarrah 01:28:35 12/28/06 Very nice man!! - Kong ZTT GT28RS MD 13:51:30 12/28/06
Post a Followup	You cannot reply to this message because you are not logged in.