Subject	Nope, haven't had a consult hooked up. What what I be
Posted by	BadZCar (FL) on May 08, 2001 at 9:27 PM
	This message has been viewed 27 times.
In Reply To	That's what I was asking..hhmm..have you had a consult done? (n/m) posted by wesman [92TT-less ] on May 08, 2001 at 10:09 AM
Message	looking for on a consult? I run an ecu diag and it returns no problems. Timing is correct, temp is good, plugs gapped at .032 because at .035 and 20psi it was blowing out the spark, plugs look good when pulled. No intake leaks, no vaccume leaks, no loose or bad connections, all coil pack test good, cas connections and things like that are all tight and good, compression is 150 across the board, leakdown is 4% when cold which is good, I'm at a loss... IZCC#204 Stage "Blah Blah Blah" Current Dyno 488hp/512ft lbs @ 5400 If it sounds like a lawnmower, it's most likely a Honduh. VTECH - TYPE R (bwahahaha)
Follow Ups	OK, ditching the 2530's for other turbos, need suggestions. - BadZCar (FL) 18:45:31 05/07/01 Yes TD05s have external gates also>>>>>> - NONE 18:49:56 05/07/01 Td-05 is direct bolt on...external wastegates..very nice (n/m) - wesman [92TT-less ] 18:50:10 05/07/01 Gonna sell those HKS ? Lemme know (n/m) - wesman [92TT-less ] 18:51:01 05/07/01 Well, the 2530's are rated at 310 each>> - F8IZHIS 18:57:50 05/07/01 Fred just put in 18G's for another comparison (n/m) - wesman [92TT-less ] 19:04:32 05/07/01 Hmmm, something just isn't right then... I hit the - BadZCar (FL) 19:29:22 05/07/01 did you check a/f ratios >> - Kiwi_Z 20:01:52 05/07/01 Haven't been back to the dyno since I installed the AFC.. - BadZCar (FL) 20:16:49 05/07/01 You should be WAY over 488 - F8IZHIS 20:29:02 05/07/01 I R E A L L Y hope so..... Otherwise I'm gonna load the - BadZCar (FL) 20:42:24 05/07/01 550 rwhp on stock motor? that's not going to be easy. - Bernie 21:27:20 05/07/01 How bout some 2835's :) (n/m) - Rob (Miami) 21:36:19 05/07/01 Well we have a couple of surprises in store for ya - Ste?myZ(ZtoyZ.NET©) 10:20:21 05/08/01 hehe... cool. u polishing the housings or something? (n/m) - Bernie 10:51:06 05/08/01 you won't hit that on an automatic... - drizzt3117 09:13:07 05/08/01 What were your compression #'s beforehand ? (n/m) - wesman [92TT-less ] 23:16:11 05/07/01 Before what? They are 150 across the board now with 2mm - BadZCar (FL) 08:44:00 05/08/01 That's what I was asking..hhmm..have you had a consult done? (n/m) - wesman [92TT-less ] 10:09:35 05/08/01 Nope, haven't had a consult hooked up. What what I be - BadZCar (FL) 21:27:50 05/08/01 TD05's are the way to go. - Good2Zya 20:16:06 05/07/01 310ps.... about 295-300 hp. plus, that's at 24psi, not - Bernie 21:24:43 05/07/01 SO, what in the holy hell is wrong with my car Bernie? - BadZCar (FL) 21:54:46 05/07/01 lol... there could be a million and 1 things doing it. - Bernie 09:51:28 05/08/01 Actually rated at 310 HP @ 14-15 PSI unless HKS was wrong - F8IZHIS 00:05:23 05/08/01 those HKS USA guys are ALWAYS misinformed. they didn't - Bernie 09:57:37 05/08/01 TD05s all the way>>> - safZ 19:34:51 05/07/01 Incon GT2835 LOL , Good for 900HP LOL (n/m) - MikeH(Phoenix) 20:39:11 05/07/01
Post a Followup	You cannot reply to this message because you are not logged in.