Subject	The PE1420 kit has a brass restrictor...
Posted by	ltd on November 21, 2006 at 9:43 PM
	This message has been viewed 197 times.
In Reply To	Your Thanksgiving Turbo Treat! GT turbos, ALREADY JETTED. posted by Ash's Z on November 21, 2006 at 04:27 PM
Message	...that sits in the oil feed and doubles as a taper to make the stock flare fitting work. But I'm sure you knew that. It seems most turbos require some form of external protection from the oil pressure in our vehicles... be interesting to pull apart the IHI turbos and see if the jet restriction is similar to that of your garrett counterpart or not.
Follow Ups	Your Thanksgiving Turbo Treat! GT turbos, ALREADY JETTED. - Ash's Z 16:27:16 11/21/06 always thinking ahead... (n/m) - inf 16:31:58 11/21/06 good info. Considering there are 2 2530's sitting on my - spotz 16:45:21 11/21/06 Very nice info - - bankruptedz 16:46:04 11/21/06 Nice (n/m) - Spongerider :) 16:58:23 11/21/06 Something that may be of interest to you. - Ash's Z 17:14:44 11/21/06 That is not why I responded to that link. - Spongerider :) 17:23:21 11/21/06 I understand why you responded. Just linked to it as I - Ash's Z 17:32:36 11/21/06 OK. Your MASSIVES (1) in tests flow more air - 240Z FeO2 19:00:52 11/21/06 I'm working on the 2.5" pipe kit just about every day. - Ash's Z 20:23:12 11/21/06 [Total hits: more than 6] :P (n/m) - vorpalZ 00:09:50 11/22/06 Nice ! (n/m) - The Devils Z 07:27:45 11/22/06 Maybe the newer GT have the built in orfice. But - AzHeat 17:57:46 11/21/06 It is possible that they weren't all this way. I know these - Ash's Z 18:03:17 11/21/06 The damage to the GT2530's was FOD to the comp wheel. - Ash's Z 18:06:29 11/21/06 your post says you have two dead cartridges?? (n/m) - AzHeat 19:56:40 11/21/06 compressor wheels are part of the cartridge (n/m) - aliaZ 20:05:14 11/21/06 Yep, both of them suffered compressor wheel FOD. (n/m) - Ash's Z 20:20:25 11/21/06 What got sucked in both turbos? (n/m) - AzHeat 20:40:49 11/21/06 No idea. Ask Mike Lapoore - it was his car before DEe - Ash's Z 20:45:34 11/21/06 Only one turbo was bad. I sold the one good turbo to - The Devils Z 04:57:32 11/22/06 what does it mean to "jet the oil feed lines?" - Zlicious (Seattle) 19:02:46 11/21/06 Ok, so ball-bearing turbos require less oil than non-ball - Zlicious (Seattle) 19:14:00 11/21/06 Correct. One thing that might be occuring also is not - Ash's Z 20:39:09 11/21/06 hmm. I've laid down a smoke screen during a road trip (very - Zlicious (Seattle) 20:50:20 11/21/06 Did you use the lines provided by HKS with the 2530's - Ash's Z 21:15:50 11/21/06 my mechanic did the install. I'm guessing he used stock - Zlicious (Seattle) 21:47:35 11/21/06 one turbo was used, one was "rebuilt" - Zlicious (Seattle) 21:49:03 11/21/06 The restricted lines were in response to noted failures - CaliguyPurdue 18:11:14 11/21/06 I hear ya - bankruptedz 18:40:06 11/21/06 Beings that the restrictor is 0.035" and aftermarket lines - Ash's Z 20:17:39 11/21/06 Its interesting that HKS oil lines have restrictors built in - ztunerz 18:44:45 11/21/06 It is. Do you know the orifice size in the HKS jets? (n/m) - Ash's Z 20:45:05 11/21/06 Very Very small - EricTTZ 21:33:09 11/21/06 wooow... thats small (n/m) - SpecNATT (Houston) 21:58:07 11/21/06 I made my own by welding shut a fitting and then - AzHeat 22:50:43 11/21/06 And my new turbos will be ready when? (n/m) - Izzy 19:34:41 11/21/06 Re: Your Thanksgiving Turbo Treat! GT turbos, ALREADY JETTED - wrxfl 19:52:32 11/21/06 My personal experience with my 700s - Seb (specialty-Z) 21:02:06 11/21/06 sorry for the short brief post.... - Seb (specialty-Z) 21:03:06 11/21/06 No problem - what size orifice are you using in your jets? - Ash's Z 21:14:54 11/21/06 Re: No problem - what size orifice are you using in your jet - Seb (specialty-Z) 21:37:12 11/21/06 my gt2560 bb turbos smoked slightly, over time a build up of - SpecNATT (Houston) 21:51:21 11/21/06 my Gt28rs has no restrictor and runs an open pipe - The Devils Z 05:00:07 11/22/06 what do you mean by "open pipe"? - Seb (specialty-Z) 10:34:26 11/22/06 I was not clear enuff .. and I thought about it after - The Devils Z 17:57:35 11/22/06 The PE1420 kit has a brass restrictor... - ltd 21:43:53 11/21/06 sweet info Ash. Ill have to see what turbos>> - Shawn Lane(NO VA) 22:13:40 11/21/06 Perhaps the biggest reason why you should look into - smartbomb 23:06:31 11/21/06 Can you elaborate on the point about water plumbing? - RSR 07:53:08 11/22/06 My guess would be that some people simply don't use - sfarrah 10:35:20 11/22/06 Ah, ok. (n/m) - RSR 10:41:13 11/22/06 No you jsut have to hook up the water to them. (n/m) - smartbomb 11:58:53 11/22/06 im no fluid dynamics expert, but... - AntiHero 10:23:28 11/22/06
Post a Followup	You cannot reply to this message because you are not logged in.