Subject	Correct. They are machined for the GT28 10-blade
Posted by	Ash's Z on November 18, 2006 at 4:39 PM
	This message has been viewed 117 times.
In Reply To	And you're on 4bolt housings right? posted by zboost(tx) on November 18, 2006 at 03:41 PM
Message	76-trim turbine (same dimensions as the 9-blade 76-trim turbine in the native GT28RS). I was concerned that the OEM 5-speed housings might choke up the exhaust flow at higher boost and revs, but apparently that makes very little difference - most of the flow difference has come from punching out the bore for this larger wheel. [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	AshsZ2 - Ultimate Street Z - DYNO CHARTS: 700RWHP - Ash's Z 15:13:26 11/18/06 Cool! (n/m) - dream Z (MD) 15:18:18 11/18/06 Re: Cool! - Bluetorch Motorsports 19:01:16 11/18/06 Nice! - sfpearl300zTT 15:24:11 11/18/06 2nd! (n/m) - BradZ (FL) 18:40:23 11/18/06 Awesome!!! About the misfire, update us when you install - Faisal 15:41:12 11/18/06 And you're on 4bolt housings right? - zboost(tx) 15:41:28 11/18/06 Correct. They are machined for the GT28 10-blade - Ash's Z 16:39:08 11/18/06 Nice! Congrats again on building such an awesome machine! (n/m) - TheTwinZ (Peru) 15:46:11 11/18/06 Nice, Devil Z is gone? (n/m) - Izzy 15:51:46 11/18/06 amazing...nice work - Cull1990Red300zx 15:52:20 11/18/06 Nice work. How come the top dyno chart shows more - AzHeat 16:04:59 11/18/06 I noted that too - I think the gain setting when using - Ash's Z 16:36:42 11/18/06 the A/F is richer on the top chart as well. I think that - boileralum 17:30:35 11/18/06 Nice work Ash! - Booster (MD) 17:06:20 11/18/06 It must suck going to the dyno - Spddracer 17:30:51 11/18/06 Looking good (n/m) - TTFairladyZ 17:58:54 11/18/06 Nice work, how much h.p. is enough? - Red Z 18:08:39 11/18/06 2nd... (n/m) - Booster (MD) 18:37:25 11/18/06 Really, for street applications, it is far too much. When I - Ash's Z 18:54:13 11/18/06 sissy, get some MT ET radials and solve your traction probs (n/m) - Z32POWER.com 20:34:46 11/18/06 oh yea, forgot the ;) (n/m) - Z32POWER.com 20:35:20 11/18/06 Nice that the boost creeps instead of drops. - Red Z 20:58:13 11/18/06 It only creeps at these lower boost levels. When running - Ash's Z 21:26:58 11/18/06 does fluctuation on the graph always mean misfire?.. - naZeer (Dallas) 18:46:29 11/18/06 In this case, it is definately misfire causing it. The EBC - Ash's Z 18:57:23 11/18/06 heavy misfire - Z32POWER.com 20:33:24 11/18/06 Yeah, and if the smoothing was set to zero, you would - Ash's Z 21:28:14 11/18/06 what plugs are you running? - z324u 20:24:59 11/18/06 Good idea. I shaved the plug bosses and am using platinum - Ash's Z 21:25:56 11/18/06 Not to mention the melting point of - Kong ZTT GT28R MD 21:54:51 11/18/06 oh.. and Detonation temps... - Kong ZTT GT28RS MD 17:27:56 11/19/06 BKR6ES should be close. 19mm reach, non projectied tip - z324u 09:45:55 11/19/06 Might help to index them too. (n/m) - ni[X]it 22:45:49 11/18/06 You're 30 HP short of 700. Symantics. - ni[X]it 22:45:26 11/18/06 Re: You're 30 HP short of 700. Symantics. - H-Power 23:21:59 11/18/06 This why ash's claim to fame is null and void. - Spongerider :) 02:10:01 11/19/06 No claim to any fame was intended. I've built higher-HP - Ash's Z 10:20:40 11/19/06 SAE corrected, yes. Not trying to confuse anyone. - Ash's Z 00:01:00 11/19/06 Sweet Ash, your car is a beast I must say.... - flyboyzack 02:29:17 11/19/06
Post a Followup	You cannot reply to this message because you are not logged in.