Subject	Re: just curious if you have a tuning setup like the ZEM
Posted by	maTTz32 on November 07, 2006 at 2:35 AM
	This message has been viewed 55 times.
In Reply To	just curious if you have a tuning setup like the ZEM posted by zxtuner161 on November 07, 2006 at 01:12 AM
Message	An injector not performing properly should see a lean condition in that cylinder/bank And some answers on this page "02 sensor feedback" of the AEM forums: [ http://forum.aempower.com/forum/index.php/topic,796.0.html ] Which says: Does it adust injector pulse widths on both banks independently? Yes, based on which injector (cylinder) was assigned to each O2 sensor. :and you can't control each individual bank a/f wise...how would you benifiet running dual widebands, other than just seeing what each side is. Also, what factors make the a/f different in each bank?
Follow Ups	AEM setup with WB O2 for each bank - maTTz32 23:55:31 11/06/06 I ordered this for my EMS>>>> - zboost(tx) 00:06:07 11/07/06 Re: I ordered this for my EMS>>>> - maTTz32 00:28:05 11/07/06 Exactly, if you get 2 widebands you completley eliminate - zboost(tx) 07:14:09 11/07/06 One thing I was questioning.. - Kong ZTT GT28R MD 02:06:00 11/07/06 No, while it has the OPTION to do that - zboost(tx) 07:44:36 11/07/06 Oh ok... Gotcha.. - Kong ZTT GT28R MD 12:52:49 11/07/06 Its good to have them 12-18" from the turbo (n/m) - kryptonite729@VP 13:04:43 11/07/06 same here, I'll just put them in the TP's. (n/m) - zboost(tx) 14:40:07 11/07/06 just curious if you have a tuning setup like the ZEM - zxtuner161 01:12:00 11/07/06 if a vaccum hose pops off, a gasket blows (inlet/outlet) - Kong ZTT GT28R MD 02:07:43 11/07/06 wouldn't you notice that on both sides though? - zxtuner161 02:12:00 11/07/06 not necessarily.. - Kong ZTT GT28R MD 02:18:31 11/07/06 so basically if i had a issue with the car with the wideband - zxtuner161 02:38:51 11/07/06 Re: so basically if i had a issue with the car with the wide - maTTz32 02:51:54 11/07/06 couldn't you weld in a bung and switch it over - zxtuner161 03:22:21 11/07/06 you sure can.. - Kong ZTT GT28R MD 03:28:15 11/07/06 thats probably what im going to end up doing. - zxtuner161 09:09:38 11/07/06 Re: couldn't you weld in a bung and switch it over - maTTz32 06:03:00 11/07/06 The only problem with going with one sided widebands - Kong ZTT GT28R MD 03:15:26 11/07/06 Exactly ..that is why I did this - The Devils Z 04:04:40 11/07/06 do 350Zs have true dual exhaust ? (n/m) - The Devils Z 04:06:21 11/07/06 Most aftermarket exhaust's are. Not sure about stock - zxtuner161 09:04:51 11/07/06 Re: just curious if you have a tuning setup like the ZEM - maTTz32 02:35:41 11/07/06 That falls under troubleshooting. - zxtuner161 02:45:22 11/07/06 there are wires that come from the wideband itself.. - Kong ZTT GT28R MD 02:09:38 11/07/06 Re: there are wires that come from the wideband itself.. - maTTz32 02:21:09 11/07/06 On the wideband itself.. - Kong ZTT GT28R MD 02:25:40 11/07/06 ditto .. look at my install I posted above for the - The Devils Z 04:08:47 11/07/06 datalogging ftw - zboost(tx) 08:07:20 11/07/06 The AEM wideband will allow data logging .. (n/m) - The Devils Z 08:36:11 11/07/06 The ones you have? - zboost(tx) 08:38:17 11/07/06 to the Zem or the EMS.. - Kong ZTT GT28R MD 12:54:48 11/07/06 the AEM UEGO widebands have extra wires for the - The Devils Z 13:43:30 11/07/06 Of course, they all do. - zboost(tx) 14:39:24 11/07/06 I said "will allow" ..... ???? maybe I'm just too tired ... (n/m) - The Devils Z 19:34:52 11/07/06 the AEM GB is a good deal .. you should take advantage - The Devils Z 04:07:23 11/07/06 Buy the AEM without the WIdeband get to wide band the - natottz 07:19:28 11/07/06 Re: Buy the AEM without the WIdeband get to wide band the - maTTz32 07:36:02 11/07/06 Where did you read this? (n/m) - zboost(tx) 07:45:26 11/07/06 Re: Where did you read this? - maTTz32 09:46:48 11/07/06 I believe that was an older version of the guage. - BOOZTD 3 10:28:15 11/07/06 my goes as low as 8 to 1 you will not have any - natottz 08:04:35 11/07/06
Post a Followup	You cannot reply to this message because you are not logged in.