Subject	Well after owning 2 other z32's...
Posted by	cubanguerrilla on October 31, 2006 at 8:55 AM
	This message has been viewed 60 times.
In Reply To	Please search. Then get SMICs. posted by BigTDogg (MA) on October 31, 2006 at 08:52 AM
Message	I went with the apollo for looks...im not a newbie to the z but I thought the loss between the smic and fmic wasnt that big of a deal....
Follow Ups	FMIC vs SMIC - cubanguerrilla 08:46:29 10/31/06 Please search. Then get SMICs. - BigTDogg (MA) 08:52:38 10/31/06 Well after owning 2 other z32's... - cubanguerrilla 08:55:00 10/31/06 Think again... - BigTDogg (MA) 09:00:47 10/31/06 apollo flows the same as stock and it hurts engine cooling (n/m) - spyhunterTT(nj) 09:07:16 10/31/06 Big differences >> - Ash's Z 15:46:58 10/31/06 Thanks I am going SMIC but..... - cubanguerrilla 09:09:52 10/31/06 Re: Thanks I am going SMIC but..... - spyhunterTT(nj) 09:16:12 10/31/06 Last fish - BigTDogg (MA) 09:19:58 10/31/06 hks (n/m) - AxleZTTic 09:21:23 10/31/06 No ducts available for them, so they're off my "Good" list. (n/m) - BigTDogg (MA) 09:52:24 10/31/06 wtfe (n/m) - Guapo 09:55:24 10/31/06 After comparing z1 and ash - cubanguerrilla 10:04:07 10/31/06 neither (n/m) - Guapo 10:12:57 10/31/06 I certianly don't disagree... - BigTDogg (MA) 10:15:44 10/31/06 HAHAHAAH ... yeah, the HKS might not be as pretty on a mod - Guapo 10:27:18 10/31/06 :P - BigTDogg (MA) 12:11:26 10/31/06 haha.. thats what I said "500rwhp is all I want" - Kong ZTT GT28R MD 10:32:05 10/31/06 Re: After comparing z1 and ash - SactoTodd 10:27:00 10/31/06 Re: Re: After comparing z1 and ash - cubanguerrilla 10:55:38 10/31/06 Dude, he searched...just be thankful for that. (n/m) - BigTDogg (MA) 12:57:45 10/31/06 What are you talking about? The Sport-SMICs use OEM ducts. - Ash's Z 13:11:27 10/31/06 What type of endtanks do the Z1 IC's use? (n/m) - BigTDogg (MA) 14:41:31 10/31/06 They look like they are - Kong ZTT GT28R MD 14:48:47 10/31/06 looked cast to me when I installed mine :/ (n/m) - BigTDogg (MA) 15:10:17 10/31/06 They are. It is aluminum sheet that has been cut and bent - Ash's Z 15:35:17 10/31/06 Pic >> - Ash's Z 15:44:36 10/31/06 Do Cast endtanks - Kong ZTT GT28R MD 16:07:24 10/31/06 I know the cast endtanks I am using flow better than the - Ash's Z 20:09:44 10/31/06 Looking forward to it! (n/m) - Kong ZTT GT28R MD 22:38:40 10/31/06 If you went with a FMIC.. - Kong ZTT GT28R MD 10:15:22 10/31/06 I keep my FMIC because... - Kong ZTT GT28R MD 10:14:25 10/31/06 2nd!! (n/m) - 1badz32 (MN) 11:33:45 10/31/06
Post a Followup	You cannot reply to this message because you are not logged in.