Subject	Re: I have a dyno session scheduled for Friday where I will
Posted by	Gho32 on October 25, 2006 at 1:09 PM
	This message has been viewed 164 times.
In Reply To	I have a dyno session scheduled for Friday where I will posted by Ash's Z on October 25, 2006 at 12:21 PM
Message	I'd like to see which performs better.. SMIC or a FMIC at the same psi 'pre-intercooler' since that's what you're looking at once you reach the peak efficiency of the turbos.
Follow Ups	turbo and intercooler set up question - Zski 11:19:30 10/25/06 Stillen SMIC $999.00 (KYLE) (n/m) - Guapo 11:21:25 10/25/06 don't forget the ducts (n/m) - vorpalZ 11:23:21 10/25/06 2nd. (n/m) - YugoBernie (NoVA) 11:24:42 10/25/06 Good point (+$199). (n/m) - Scotts94z32 11:24:55 10/25/06 point still stands (n/m) - Guapo 11:27:11 10/25/06 $949.99 @ Ultimate Z - Coz matched it, I'm sure Kyle can too - ZLover4Life 20:08:38 10/25/06 I have and love the Z1 ICs - BigTDogg (MA) 11:32:24 10/25/06 I flowtested a few more ICs yesterday: - Ash's Z 11:32:25 10/25/06 p.s. Would like to get a Greddy and Stillen SMIC to test. - Ash's Z 11:34:21 10/25/06 was just gonna inquire about those two brands (n/m) - Seb (specialty-Z) 11:35:20 10/25/06 I tried calling you about half an hour ago. :) - Ash's Z 11:36:27 10/25/06 Link --> - Inzane 11:41:56 10/25/06 I have some concerns with that data posted... - Ash's Z 12:09:06 10/25/06 Can you really say that? - Kenny 12:12:23 10/25/06 What I meant by that was when testing an intercooler, it - Ash's Z 12:16:43 10/25/06 Okie. - Kenny 12:22:19 10/25/06 I could try testing at different pressures up to what the - Ash's Z 12:28:59 10/25/06 Nice. Shoot me the data if you like, I'll extrapolate the... - Kenny 12:38:40 10/25/06 It depends HEAVILY on the individual designs. - CaliguyPurdue 22:30:54 10/25/06 I acknowledge that the methodologies used may have been - Inzane 12:43:52 10/25/06 2nd. (n/m) - Kenny 12:45:46 10/25/06 I agree. I just wonder what was different in the testing - Ash's Z 13:05:36 10/25/06 Your answer lies in the wonders of differential equations... - CaliguyPurdue 22:32:14 10/25/06 I didn't see you post that in tech, so here's a question. - Kenny 11:40:33 10/25/06 We tested both of the cores of each FMIC independent - Ash's Z 12:10:28 10/25/06 Cool, thanks Ash. (n/m) - Kenny 12:13:46 10/25/06 Ash: Could you do a pressure vs flow graph - Jmartz 11:46:27 10/25/06 I have a dyno session scheduled for Friday where I will - Ash's Z 12:21:39 10/25/06 Re: I have a dyno session scheduled for Friday where I will - Gho32 13:09:11 10/25/06 =) That's one of the test methods I had in mind. - Ash's Z 16:43:32 10/25/06 Where will you install your thermocouples for "Temp IN" - Inzane 14:07:50 10/25/06 NPT bungs are already installed in the pipes just before and - Ash's Z 14:22:39 10/25/06 Excellent! (n/m) - Inzane 14:41:45 10/25/06 How about a set of massives with the reducers on both ends. (n/m) - Woody75 (Denver) 11:51:55 10/25/06 I'm considering building set of MASSIVES with 2.0" inlets - Ash's Z 12:12:11 10/25/06 I'd be interested in seeing the test with the reducers. (n/m) - sfarrah 15:34:07 10/25/06 LMAO at the apollo fmic. (n/m) - zboost(tx) 12:11:47 10/25/06 Yeah, I expected it to do a little better than that, however - Ash's Z 12:15:17 10/25/06 looks like the sport smics should be sufficient (n/m) - boostedzxtt 12:51:39 10/25/06 woudl you like a GReddy 3-row to test? - Kong ZTT GT28R MD 15:43:13 10/25/06 I am talking about my FMIC of course.. - Kong ZTT GT28R MD 16:01:12 10/25/06 I'd do it. I'll pay return shipping on it too. I'll only - Ash's Z 16:39:35 10/25/06 sure thing.. - Kong ZTT GT28R MD 21:35:39 10/25/06 are these w/ 2.5" IC pipes (n/m) - ARA300ZX 20:37:28 10/25/06 *** Chroming VS Polishing *** - Zski 11:35:47 10/25/06 PC it and be done, or chrome it, polishing takes too much - BigTDogg (MA) 11:43:27 10/25/06 2nd, hell of a lot less work in prep work too (n/m) - spyhunterTT(nj) 11:47:09 10/25/06 The problem with chrome is... - 92fairladyz (Yokosuka, Japan) 17:50:20 10/25/06 i got my Greddy's for $650shipped NIB - Rickytl (ma) 12:04:10 10/25/06 plus dont they fit the OEM ducts? - LJZTT 12:08:13 10/25/06 correct - Rickytl (ma) 12:09:42 10/25/06 search (n/m) - SactoTodd 12:40:07 10/25/06 I did... but i am Looking for *up to date* opinions (n/m) - Zski 12:42:40 10/25/06 pot/kettle (n/m) - SactoTodd 12:50:58 10/25/06 since we're on the topic, has anyone constructed ducts? - kanigie 15:23:23 10/25/06 you forgot TDMWORKS SMIC's or ARC SMIC's (n/m) - ArubaDave 18:44:51 10/25/06
Post a Followup	You cannot reply to this message because you are not logged in.