Subject	John Abeler manifolds help with this
Posted by	zboost(tx) on October 24, 2006 at 11:14 AM
	This message has been viewed 536 times.
In Reply To	answer inside >>> posted by scubasteve (waiting for parts) on October 24, 2006 at 11:10 AM
Message	at least that's what I understand from his design. It tilts the turbo slightly to allow for a straighter DP. I think. BEST 1/4mile 11.92 @ 117mph. PUMP gas, true 11 sec. street car :) stock turbos/injectors "yo yo. writing this one in jail - tight300zx" I hope you got soap on a rope?? (n/m) - Spongerider :) 19:14:08 04/01/04 we'll know if the screen name changes ;) (n/m) - SactoTodd 19:32:36 04/01/04 "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - - DC 21:11:01 02/18/04 (the "holes" were located on the exhaust)
Follow Ups	Why do we STILL not have this available ... - Kong ZTT GT28R MD 02:42:36 10/24/06 Here are some better pics.. - Kong ZTT GT28R MD 02:58:26 10/24/06 on my next BIG build.. If I dont go external wastegate.. - Kong ZTT GT28R MD 03:00:54 10/24/06 Divergence in excess of ~ 12 degrees causes turbulance. - CaliguyPurdue 11:19:29 10/24/06 mmm yes. a cone to to would be best - scubasteve (waiting for parts) 11:40:51 10/24/06 Um i guess because.... - Tuppidsay 03:21:45 10/24/06 its wasn't more power.. - Kong ZTT GT28R MD 03:22:56 10/24/06 plus, external wastegates holds better boost. (n/m) - Qwk Z (hawaii) 03:23:54 10/24/06 true... - Kong ZTT GT28R MD 03:25:48 10/24/06 Isn't Greg Dupree making a - Qwk Z (hawaii) 03:43:42 10/24/06 I heard bits n peices.. I would love to hear more on it tho. (n/m) - Kong ZTT GT28R MD 06:19:29 10/24/06 I thought you meant v-band clamps - BigTDogg (MA) 08:41:36 10/24/06 Why don't you pay someone to make you one? (n/m) - SactoTodd 09:29:24 10/24/06 Supra guys are making huge HP gains just by - Talisman (New Orleans) 09:38:28 10/24/06 Re: Supra guys are making huge HP gains just by - ouikikazz 10:44:30 10/24/06 its not about gain or loss ..its about area under the - The Devils Z 12:08:56 10/24/06 The 4" is only good for the bigger turbos though - flyboyzack 12:03:33 10/24/06 That would a require a T3 housing right? - zboost(tx) 11:06:26 10/24/06 No.. that is bolting up to OUR t25 turbo.. - Kong ZTT GT28R MD 13:40:46 10/24/06 answer inside >>> - scubasteve (waiting for parts) 11:10:28 10/24/06 John Abeler manifolds help with this - zboost(tx) 11:14:26 10/24/06 the v2's do, yes. i have the v1's which are stock location - scubasteve (waiting for parts) 11:33:24 10/24/06 3" centerline radius at ATPturbo.com - Kong ZTT GT28R MD 14:04:58 10/24/06 Re: 3" centerline radius at ATPturbo.com (n/m) - octavian-z 17:23:01 10/24/06 Any "tilt" is in my latest design.... - I-xclr8 12:15:05 10/24/06 yes, do those DP's bolt to regular TT TP's? - zboost(tx) 12:32:55 10/24/06 You can use my design which is built in external - AzHeat 11:48:59 10/24/06 what exhaust housing do you use? (n/m) - zboost(tx) 11:54:19 10/24/06 Mine was made by INCON which has divider cast in. (n/m) - AzHeat 17:29:49 10/24/06 i hope no amount of exhaust leaks between the divider - scubasteve (waiting for parts) 12:32:03 10/24/06 I dont see the point in that, other than just for the sound - Kong ZTT GT28R MD 13:43:29 10/24/06 How are you ensuring that there isn't any leakage between - Ash's Z 15:37:42 10/24/06 my turbine housing has built in divider - AzHeat 17:27:46 10/24/06 Ah, thanks for the clarification - I was a bit concerned - Ash's Z 18:29:16 10/24/06
Post a Followup	You cannot reply to this message because you are not logged in.