Subject	You wont pull that bolt through the end of the mount.
Posted by	Ash's Z on September 26, 2006 at 2:58 PM
	This message has been viewed 60 times.
In Reply To	Ford motor mount failure: posted by Zluster(Abudan) on September 26, 2006 at 01:45 PM
Message	Once it is bolted back in place, you will pull that bolt tight and the head of it will secure the mount without any motion. I suspect it was due to not properly tightening the nut holding the mount in place.. [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	Ford motor mount failure: - Zluster(Abudan) 13:45:38 09/26/06 thats not bad , i think i will pick up a set also (n/m) - AllAboutDaZ 13:54:28 09/26/06 Re: thats not bad , i think i will pick up a set also - z32ryan 22:47:05 09/26/06 So basically, OEM is best. (n/m) - BigTDogg (MA) 13:56:44 09/26/06 I think this was an isolated case caused by a defective.... - Zluster(Abudan) 14:27:01 09/26/06 I'm running the Ford ones on both my Z's with out issue (n/m) - Woody75 (Denver) 14:30:04 09/26/06 Are there other advantages over cost? (n/m) - BigTDogg (MA) 14:36:01 09/26/06 Lifetime warrante from autozone. (n/m) - Zluster(Abudan) 15:30:40 09/26/06 The oems ALWAYS fail. always. ford > oem for strength (n/m) - AntiHero 15:29:22 09/26/06 2 engine pulls, 2 clutch changes, 15 years, - Billteed1 16:14:55 09/26/06 every z32 motor i pull has had alteast one mount shot. - SpecNATT (Houston) 19:22:56 09/26/06 Noltecs suck (n/m) - Guapo 19:31:01 09/26/06 2nd (n/m) - Shawn300zTT GT28R MD 14:26:39 09/27/06 "like your going to rip a bunnies head off" - nemo1080 22:47:21 09/26/06 these are taller than OEM, right? (n/m) - aliaz 14:04:18 09/26/06 Not by much. (n/m) - Woody75 (Denver) 14:15:52 09/26/06 Not by much: - Zluster(Abudan) 14:24:58 09/26/06 OEM all the way... - Shawn300zTT GT28R MD 14:19:16 09/26/06 You wont pull that bolt through the end of the mount. - Ash's Z 14:58:16 09/26/06 The nut was still torqued down.... - Zluster(Abudan) 21:25:44 09/26/06 yikes, how many miles is that? (n/m) - spyhunterTT(nj) 15:11:00 09/26/06 ~20k...... - Zluster(Abudan) 15:30:10 09/26/06 how much grease did you need? (n/m) - Spee 21:14:15 09/26/06 You are brutal. LOL - brahmabull (Hartford, CT) 21:26:30 09/26/06 I use only butter.....all natural..... (n/m) - Zluster(Abudan) 01:07:48 09/27/06 oh man.. LOL (n/m) - Shawn300zTT GT28R MD 02:47:30 09/27/06
Post a Followup	You cannot reply to this message because you are not logged in.