Subject	I think this was an isolated case caused by a defective....
Posted by	Zluster(Abudan) on September 26, 2006 at 2:27 PM
	This message has been viewed 41 times.
In Reply To	So basically, OEM is best. (n/m) posted by BigTDogg (MA) on September 26, 2006 at 01:56 PM
Message	...part, The other mount I had did not have the same concave top, and held up just fine. What I think caused this was that once installed the nuts acted like a big stud extractor, a stud extractor extracting something you dont want extracted. Even taken a large socket and a nut to pull out a stud thats been pressed in? Same idea here, just by defect instead of intention. --------------------------- The Gods are Just. Rob.M (Down Shift Magazine) ripped me off! Did he rip you off too? Let me know! Email me!
Follow Ups	Ford motor mount failure: - Zluster(Abudan) 13:45:38 09/26/06 thats not bad , i think i will pick up a set also (n/m) - AllAboutDaZ 13:54:28 09/26/06 Re: thats not bad , i think i will pick up a set also - z32ryan 22:47:05 09/26/06 So basically, OEM is best. (n/m) - BigTDogg (MA) 13:56:44 09/26/06 I think this was an isolated case caused by a defective.... - Zluster(Abudan) 14:27:01 09/26/06 I'm running the Ford ones on both my Z's with out issue (n/m) - Woody75 (Denver) 14:30:04 09/26/06 Are there other advantages over cost? (n/m) - BigTDogg (MA) 14:36:01 09/26/06 Lifetime warrante from autozone. (n/m) - Zluster(Abudan) 15:30:40 09/26/06 The oems ALWAYS fail. always. ford > oem for strength (n/m) - AntiHero 15:29:22 09/26/06 2 engine pulls, 2 clutch changes, 15 years, - Billteed1 16:14:55 09/26/06 every z32 motor i pull has had alteast one mount shot. - SpecNATT (Houston) 19:22:56 09/26/06 Noltecs suck (n/m) - Guapo 19:31:01 09/26/06 2nd (n/m) - Shawn300zTT GT28R MD 14:26:39 09/27/06 "like your going to rip a bunnies head off" - nemo1080 22:47:21 09/26/06 these are taller than OEM, right? (n/m) - aliaz 14:04:18 09/26/06 Not by much. (n/m) - Woody75 (Denver) 14:15:52 09/26/06 Not by much: - Zluster(Abudan) 14:24:58 09/26/06 OEM all the way... - Shawn300zTT GT28R MD 14:19:16 09/26/06 You wont pull that bolt through the end of the mount. - Ash's Z 14:58:16 09/26/06 The nut was still torqued down.... - Zluster(Abudan) 21:25:44 09/26/06 yikes, how many miles is that? (n/m) - spyhunterTT(nj) 15:11:00 09/26/06 ~20k...... - Zluster(Abudan) 15:30:10 09/26/06 how much grease did you need? (n/m) - Spee 21:14:15 09/26/06 You are brutal. LOL - brahmabull (Hartford, CT) 21:26:30 09/26/06 I use only butter.....all natural..... (n/m) - Zluster(Abudan) 01:07:48 09/27/06 oh man.. LOL (n/m) - Shawn300zTT GT28R MD 02:47:30 09/27/06
Post a Followup	You cannot reply to this message because you are not logged in.