Subject	OEM all the way...
Posted by	Shawn300zTT GT28R MD on September 26, 2006 at 2:19 PM
	This message has been viewed 42 times.
In Reply To	Ford motor mount failure: posted by Zluster(Abudan) on September 26, 2006 at 01:45 PM
Message	I am glad that I just went OEM.. and even not with the NOLTEC or solid.. I *almost* went with solid.. but then I thought about pulling my trans and not being able to tilt the motor back.. ehh NO, This picture is not photoshopped. It took many times to take this picture. Setting up the timer, shutter speed etc, then jumping on my bike and getting the tire to spin. AIM:Shawn300zxTT "-Any closeups on the nuts? - zboost(tx) 19:17:53 08/08/05 -Not really something you want to ask another man about... (n/m) - LordZ 19:24:00 08/08/05" "I just took 45 min and scrubbed the heck out of my rear" teambushido(San Diego, CA) 19:24:51 12/11/04 -1991 Stage _ TT 5spd (Turbo Upgrade in process) -1990 Super White 2+2 Na Stage 3 Auto (Daily Driver) -1990 Cherry Red Pearl ,Auto Coupe (Parts car) -199011 Sec Eagle Talon Tsi AWD, (Sitting for now) -1996 Hyundai Sonata (Given to me for FREE , due to broken timing belt, fixed it myself and its my new DD that gets over 25 mpg! -2004 Honda CBR 600RR (Candy blue)
Follow Ups	Ford motor mount failure: - Zluster(Abudan) 13:45:38 09/26/06 thats not bad , i think i will pick up a set also (n/m) - AllAboutDaZ 13:54:28 09/26/06 Re: thats not bad , i think i will pick up a set also - z32ryan 22:47:05 09/26/06 So basically, OEM is best. (n/m) - BigTDogg (MA) 13:56:44 09/26/06 I think this was an isolated case caused by a defective.... - Zluster(Abudan) 14:27:01 09/26/06 I'm running the Ford ones on both my Z's with out issue (n/m) - Woody75 (Denver) 14:30:04 09/26/06 Are there other advantages over cost? (n/m) - BigTDogg (MA) 14:36:01 09/26/06 Lifetime warrante from autozone. (n/m) - Zluster(Abudan) 15:30:40 09/26/06 The oems ALWAYS fail. always. ford > oem for strength (n/m) - AntiHero 15:29:22 09/26/06 2 engine pulls, 2 clutch changes, 15 years, - Billteed1 16:14:55 09/26/06 every z32 motor i pull has had alteast one mount shot. - SpecNATT (Houston) 19:22:56 09/26/06 Noltecs suck (n/m) - Guapo 19:31:01 09/26/06 2nd (n/m) - Shawn300zTT GT28R MD 14:26:39 09/27/06 "like your going to rip a bunnies head off" - nemo1080 22:47:21 09/26/06 these are taller than OEM, right? (n/m) - aliaz 14:04:18 09/26/06 Not by much. (n/m) - Woody75 (Denver) 14:15:52 09/26/06 Not by much: - Zluster(Abudan) 14:24:58 09/26/06 OEM all the way... - Shawn300zTT GT28R MD 14:19:16 09/26/06 You wont pull that bolt through the end of the mount. - Ash's Z 14:58:16 09/26/06 The nut was still torqued down.... - Zluster(Abudan) 21:25:44 09/26/06 yikes, how many miles is that? (n/m) - spyhunterTT(nj) 15:11:00 09/26/06 ~20k...... - Zluster(Abudan) 15:30:10 09/26/06 how much grease did you need? (n/m) - Spee 21:14:15 09/26/06 You are brutal. LOL - brahmabull (Hartford, CT) 21:26:30 09/26/06 I use only butter.....all natural..... (n/m) - Zluster(Abudan) 01:07:48 09/27/06 oh man.. LOL (n/m) - Shawn300zTT GT28R MD 02:47:30 09/27/06
Post a Followup	You cannot reply to this message because you are not logged in.