TwinTurbo.NET: Nissan 300ZX forum - Ok, I'll answer, only cause I'm bored...(and stroked, LOL)
People Seeking Info
 
   


     
Subject Ok, I'll answer, only cause I'm bored...(and stroked, LOL)
     
Posted by BigTDogg (MA) on July 19, 2006 at 2:14 PM
  This message has been viewed 178 times.
     
In Reply To Re: so this is what I'll do turbo and all? posted by partymonster975 on July 19, 2006 at 11:31 AM
     
Message Greddy SP2 exhaust -good

Greddy turbo timer -good

2.5 split flange downpipes -good, but get Specialty Z super splits

2.5 midpipe/testpipes -good

JWT duel pop charger -good (dual :D)

JWT ECU (or ash ECU) -good

Apexi SAFC 1 (or Zemulator) -good, but I'd go SAFC IMO

Unorthodox Racing Underdrive pulley -good

Howe 2.25 Racing Radiator -good

HKS side mount intercoolers -good, or GReddy, or Stillen, or Z1 or T0Ms (http://www.tdm-works.com/) or AshSPEC, just stay away from FMICs

HKS SSQV BOV's (recirculated) -good

Hard pipe kit -good

Greddy profec b-spec 2 Boost controller (or Blitz SBC-iD) -see my post below, spec 2 = garbage, type S and Blitz, or AVC-R = good

Blitz R-VIT (not sure yet) -good

Z1 Drive shaft -good

JWT 530 BB turbos -good, but also check out Z1 GT600R kit for much less money

740cc injectors -good, make sure you get 95+ style, and you'll need 95+ style injector connectors, get from Coz @ [ www.czp.us ]

Specialty Z manifolds -good, or MSP (Mike Smiths) manis

RPS sport street clutch and flywheel -good, but I'd go Max street for power holding, or RPS carbon carbon if you can

SPL stainless steel clutch lines -good, line, singular
Border fuel rail -bad, go OEM 95+ or 300° Fuel Rail (best option)

EGR elimination kit -good

NGK PFR6B-11B cold plugs -good

Auto meter boost, water temp and oil pres. gauges -good, VDO matches stock gauges perfectly though

SX Fuel pressure regulator -not required but might be OK, search on it to find issues

4.10 gearing -good

Extrude honed upper/lower plenums -good, but better would be 60mm throttle body conversion and 2.5" IC plumbing

CP forged Pistons (stock bore) and ARP rob bolts -good, and add Eagle rods

For engine building, unless you've built motors before, I'd leave the task to Kyle at Importpartspro (IPP) or Greg and Seb at SpecialtyZ. They have short and long block packages available to choose from.




"...Downpipes own. They own everything...anything...all there ever was and will be...they should be stock on all cars. Screw the environment, emissions, noise! I love them...I shall name my first-born after them with glee..." - SeedyRom 05:13:20 10/03/02

"i love the cock" - genic 22:20:47 09/25/03

"I hope you get fucked in the ass with a pringles can." - ni[X]it 14:53:53 02/02/06

"Either ignore him or beat him up. Anything else will be over his head." - Marshall 12:28:23 08/18/04

z32baby: yeah, my memory sucks balls
DJ Juiced: What's your memory doing this friday night? ;)

"i've got to the point where i can drive the Z at its limits and i want more" - shadowZ 16:29:56 08/31/04

"I was way more timid then than I am now about getting in there and yanking on things." - TT XTZ 13:30:34 07/25/05

     
Follow Ups  
     
Post a
Followup

You cannot reply to this message because you are not logged in.