Subject	17# is pushing it IMHO. Given that everything is tight,
Posted by	Ash's Z on July 11, 2006 at 5:27 PM
	This message has been viewed 50 times.
In Reply To	Got the Z back from IPS posted by Chase86(WV) on July 11, 2006 at 05:07 PM
Message	as in, no boost leaks, proper base timing, good quality 93 octane pumpfuel, solid fuel system, etc, I would consider running no more than 16psi, especially on a stock bottom end. You are probably OK, but that's a little more than I would recommend. [ ashspecz.com ] [ agpowers@bellsouth.net ] Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	Got the Z back from IPS - Chase86(WV) 17:07:16 07/11/06 nice! - LJZTT 17:26:15 07/11/06 Cruising isnt too bad. Ill post some speed and RPM #'s - Chase86(WV) 17:53:08 07/11/06 should be pretty much the same as an NA (n/m) - LJZTT 21:40:42 07/11/06 logo? I see no logo. (n/m) - WAGGZ 18:41:12 07/11/06 17# is pushing it IMHO. Given that everything is tight, - Ash's Z 17:27:14 07/11/06 Interesting. Thanks for the advice. So basicly after - Chase86(WV) 17:50:20 07/11/06 Not "only" blowing hot air, but you are pushing their - Scotts94z32 18:20:59 07/11/06 Well, turbos never blow cool air under any circumstances. - Ash's Z 19:47:20 07/11/06 Thanks for the more indepth advice. I can't wait for cooler - Chase86(WV) 00:04:13 07/12/06 Did you replace the diff and subframe bushings with - CollegeBoy (Kauai) 18:00:51 07/11/06 If you don't ever track or drag race your car then don't - Z-Jay (Edmonton, AB) 18:07:16 07/11/06 Well im replacing them with something when i pull the - CollegeBoy (Kauai) 18:13:10 07/11/06 I would replace them with the softest material you can - sbarge 19:14:08 07/11/06 2nd! (n/m) - Z-Jay (Edmonton, AB) 19:27:58 07/11/06 oddly enough I get very littl enoise with my alum bushings (n/m) - Guapo 19:32:58 07/11/06 perhaps it's with the leader gears? - CollegeBoy (Kauai) 19:45:42 07/11/06 yes, the leader gears are going to be louder (n/m) - Guapo 19:46:28 07/11/06 2nd. I believe mine are louder but, im gonna mess with - Chase86(WV) 00:07:58 07/12/06 indeed (n/m) - aliaZ 21:06:16 07/11/06 ^^^Listen to this man^^^ - aliaZ 21:09:18 07/11/06 thanks for the feedback - CollegeBoy (Kauai) 00:25:54 07/12/06 Don't be a girly man, put them on. (n/m) - zboost(tx) 19:22:15 07/11/06 I don' t really mind, but I prefer for my passengers to - CollegeBoy (Kauai) 20:07:15 07/11/06 B!tces yo, just send them smiley faces. B!tches dig smiley - YugoBernie (NoVA) 20:42:03 07/11/06 Once you got the OEM ones out it's all downhill from there - sbarge 21:18:13 07/11/06 Take her over some rumble strips... - PennStateZ 21:21:09 07/11/06 lol! - CollegeBoy (Kauai) 00:25:17 07/12/06 no tangible sound difference with the ES polyurethanes - LJZTT 21:43:53 07/11/06 No I didnt replace any bushings. All OEM except for - Chase86(WV) 00:06:20 07/12/06 Also the noise I am experiencing is the same as - Chase86(WV) 00:12:11 07/12/06
Post a Followup	You cannot reply to this message because you are not logged in.