Subject	when I was shopping for ICs
Posted by	ZEngineer on July 05, 2006 at 7:42 AM
	This message has been viewed 172 times.
In Reply To	Trying to decide on intercooler upgrade... posted by turbosailor on July 04, 2006 at 11:47 PM
Message	much like you, I told myself that I'd stick to one of the trusted brands. As far as I've seen, there has never been any tests showing that one brand gives any considerable power gains over the other, and they all fit well (although the Stillen units interfere with sidemarkers), so price was my #1 concern. I waited & waited...until I scored some mint condition Greddy SMICs for $620 shipped. I suggest that as long as you're sticking to known good brands, you should wait for the best deal. _________________________________________________________________________________ "The Z is the cause and the solution to all my problems" -- Me manstretch: well, my rear end is just worn out ZEngineer24: sig quote
Follow Ups	Trying to decide on intercooler upgrade... - turbosailor 23:47:33 07/04/06 I like the ones - KAOSTT 00:04:37 07/05/06 Bigger is always better :( (n/m) - ni[X]it 07:53:37 07/05/06 does that make her a size queen? - dvlhntr 08:36:21 07/05/06 Re: Trying to decide on intercooler upgrade... - Tsefreeflow 00:58:32 07/05/06 Re: Re: Trying to decide on intercooler upgrade... - LJZTT 01:28:32 07/05/06 I had absolutely no problems fitting Greddy SMICs - ZEngineer 07:32:19 07/05/06 2nd. (n/m) - Z-Jay (Edmonton, AB) 09:28:00 07/05/06 Re: 2nd. - Tsefreeflow 10:34:55 07/05/06 I had no problem like that at all. Are you sure you used - Z-Jay (Edmonton, AB) 10:40:58 07/05/06 that's unusual, like I said, I had no issues with ANY of the - ZEngineer 10:41:29 07/05/06 what is the largest you can go - VG30DE racer 01:30:50 07/05/06 AFAIK, those would be GReddy's (n/m) - BigTDogg (MA) 10:29:29 07/05/06 You can go AshSPEC w/o a carbon cannister delete. - 92fairladyz (Yokosuka, Japan) 17:58:18 07/05/06 when I was shopping for ICs - ZEngineer 07:42:11 07/05/06 2nd, good advice. (n/m) - Waco300zx 09:47:45 07/05/06 Not all of us can be so lucky... - BigTDogg (MA) 10:31:15 07/05/06 This is where Ash *always* drops the ball. - ni[X]it 12:50:11 07/05/06 I don't recall the exact post, and I don't know if details - BigTDogg (MA) 13:14:50 07/05/06 2nd. Curious about SZ Dp's... So the new design offers - Waco300zx 13:46:40 07/05/06 How do you figure that it was a bad comparison though? - Ash's Z 22:02:31 07/05/06 I dont recall, but has anybody ever directly asked him to - ENVYMYZ 13:51:49 07/05/06 IMO, shouldn't need to be asked, should just do it - Nike (n/m) - BigTDogg (MA) 13:59:01 07/05/06 Well that's a given. So what are all the leg humpers excited - ENVYMYZ 16:46:22 07/05/06 What are you retarded? - Spongerider :) 15:28:00 07/05/06 No, but apparently they have it all figured out... - Ash's Z 21:18:44 07/05/06 Simple engineering experimentation principals Ash. - BigTDogg (MA) 08:22:58 07/06/06 Yep (n/m) - ENVYMYZ 08:52:54 07/06/06 I do agree with you that comparing single modifications - Ash's Z 12:55:32 07/06/06 OK, in that case your target market is different than - BigTDogg (MA) 13:30:14 07/06/06 The analogy was a stretch, but manifolds come in pairs - Ash's Z 14:28:30 07/06/06 *ALSO*: Putting the feelers out there: - Ash's Z 17:00:00 07/06/06 *sigh* What a load of crap. - Ash's Z 21:09:16 07/05/06 $375 for a pair of Trust aka Greddy, used. :) (n/m) - SactoTodd 13:14:04 07/05/06 Mother Effer. I need to find deals like this >:| Grrrr - BigTDogg (MA) 13:18:13 07/05/06 Hate me. :) - SactoTodd 13:20:59 07/05/06 2nd. - Kenny 13:30:34 07/05/06 My timing blows then - BigTDogg (MA) 13:31:09 07/05/06 good plan (n/m) - Guapo 13:32:19 07/05/06 Maybe one day you'll install them ;) (n/m) - CaliguyPurdue 13:41:23 07/05/06 Touche! (n/m) - shirow 15:26:09 07/05/06 I'll give you $450 if you haven't installed them yet... - BigTDogg (MA) 13:49:01 07/05/06 Are you buying mods vicariously? (n/m) - shirow 15:27:58 07/05/06 sound advice (n/m) - Guapo 10:35:44 07/05/06 Go with the Z1 sidemounts... - Joe(NoVA) 16:56:45 07/05/06
Post a Followup	You cannot reply to this message because you are not logged in.