Subject	hi
Posted by	zboost(tx) on May 18, 2006 at 12:35 PM
	This message has been viewed 32 times.
In Reply To	Correction; posted by ni[X]it on May 18, 2006 at 12:18 PM
Message	could I bed them in before I leave for ZcON? like 3 days before? then drive 500 miles to the track and race on them? Or does the bedding in have to be done right before? BEST 1/4mile 11.92 @ 117mph. PUMP gas, true 11 sec. street car :) stock turbos/injectors "yo yo. writing this one in jail - tight300zx" I hope you got soap on a rope?? (n/m) - Spongerider :) 19:14:08 04/01/04 we'll know if the screen name changes ;) (n/m) - SactoTodd 19:32:36 04/01/04 "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - - DC 21:11:01 02/18/04 (the "holes" were located on the exhaust)
Follow Ups	MSR checklist for ZCON?? - PakiHomBoy 11:41:23 05/18/06 simplified; - ni[X]it 11:48:07 05/18/06 thats exactly what i was looking for, thanks a bunch (n/m) - PakiHomBoy 11:51:05 05/18/06 Thank you! (n/m) - TT XTZ 12:00:58 05/18/06 For you long distance fellers, - ni[X]it 12:05:30 05/18/06 *fellettes (n/m) - Spee 12:08:49 05/18/06 *fellates (n/m) - Kenny 12:11:09 05/18/06 Mine, or will Bernie's do? - TT XTZ 12:11:11 05/18/06 one of two ways... - Spee 12:14:36 05/18/06 Correction; - ni[X]it 12:18:38 05/18/06 hi - zboost(tx) 12:35:22 05/18/06 The "unbed" by daily driving. Best is to bed-in as close - Scotts94z32 14:44:32 05/18/06 good point. - Spee 12:42:53 05/18/06 If you decide to install them at the track, there is not - sfarrah 12:19:27 05/18/06 Holla G/F!!! - ni[X]it 12:16:50 05/18/06 Pffft... a lot you know. She'll be putting swapping the - Dave N 12:39:25 05/18/06 she'll be doing what? (n/m) - Spee 12:45:37 05/18/06 Thanks to all for the info! - TT XTZ 12:33:49 05/18/06 how do you visually inspect wheel bearings? - ZEngineer 12:07:55 05/18/06 what, they don't do tech inspections when you break in to - Spee 12:09:58 05/18/06 Hi. - ni[X]it 12:13:07 05/18/06 no Zcooon for me - ZEngineer 12:18:45 05/18/06 Haha... - BradZ (FL) 12:20:31 05/18/06 bahaha That's great! (n/m) - ZEngineer 12:26:58 05/18/06 I can do that for you... Just give me your list. ;-) - Z-Jay (Edmonton, AB) 12:29:02 05/18/06 I've emailed you the list - ZEngineer 12:31:59 05/18/06 lift one corner at a time with tire on and off the ground... - Cap927(Boston) 12:19:12 05/18/06 I always thought that line of testing - ZEngineer 12:23:14 05/18/06 If the wheel wiggles and BJs/tie rods are tight - dogpile (still dogpile) 12:30:45 05/18/06 Thanks to Rodel for the info. - 300twinz (satx) 11:50:54 05/18/06 Is anyone bringing a jack and 2x4's? (n/m) - zboost(tx) 13:03:27 05/18/06
Post a Followup	You cannot reply to this message because you are not logged in.