Subject	I always thought that line of testing
Posted by	ZEngineer on May 18, 2006 at 12:23 PM
	This message has been viewed 31 times.
In Reply To	lift one corner at a time with tire on and off the ground... posted by Cap927(Boston) on May 18, 2006 at 12:19 PM
Message	was for bushings and ball joints condition, I didn't know it also applied for wheel bearings. I thought the only tell-tale signs were grinding sounds while driving that amplified when you turned towards the side that's damaged. Thanks. _________________________________________________________________________________ "The Z is the cause and the solution to all my problems" -- Me manstretch: well, my rear end is just worn out ZEngineer24: sig quote
Follow Ups	MSR checklist for ZCON?? - PakiHomBoy 11:41:23 05/18/06 simplified; - ni[X]it 11:48:07 05/18/06 thats exactly what i was looking for, thanks a bunch (n/m) - PakiHomBoy 11:51:05 05/18/06 Thank you! (n/m) - TT XTZ 12:00:58 05/18/06 For you long distance fellers, - ni[X]it 12:05:30 05/18/06 *fellettes (n/m) - Spee 12:08:49 05/18/06 *fellates (n/m) - Kenny 12:11:09 05/18/06 Mine, or will Bernie's do? - TT XTZ 12:11:11 05/18/06 one of two ways... - Spee 12:14:36 05/18/06 Correction; - ni[X]it 12:18:38 05/18/06 hi - zboost(tx) 12:35:22 05/18/06 The "unbed" by daily driving. Best is to bed-in as close - Scotts94z32 14:44:32 05/18/06 good point. - Spee 12:42:53 05/18/06 If you decide to install them at the track, there is not - sfarrah 12:19:27 05/18/06 Holla G/F!!! - ni[X]it 12:16:50 05/18/06 Pffft... a lot you know. She'll be putting swapping the - Dave N 12:39:25 05/18/06 she'll be doing what? (n/m) - Spee 12:45:37 05/18/06 Thanks to all for the info! - TT XTZ 12:33:49 05/18/06 how do you visually inspect wheel bearings? - ZEngineer 12:07:55 05/18/06 what, they don't do tech inspections when you break in to - Spee 12:09:58 05/18/06 Hi. - ni[X]it 12:13:07 05/18/06 no Zcooon for me - ZEngineer 12:18:45 05/18/06 Haha... - BradZ (FL) 12:20:31 05/18/06 bahaha That's great! (n/m) - ZEngineer 12:26:58 05/18/06 I can do that for you... Just give me your list. ;-) - Z-Jay (Edmonton, AB) 12:29:02 05/18/06 I've emailed you the list - ZEngineer 12:31:59 05/18/06 lift one corner at a time with tire on and off the ground... - Cap927(Boston) 12:19:12 05/18/06 I always thought that line of testing - ZEngineer 12:23:14 05/18/06 If the wheel wiggles and BJs/tie rods are tight - dogpile (still dogpile) 12:30:45 05/18/06 Thanks to Rodel for the info. - 300twinz (satx) 11:50:54 05/18/06 Is anyone bringing a jack and 2x4's? (n/m) - zboost(tx) 13:03:27 05/18/06
Post a Followup	You cannot reply to this message because you are not logged in.