Subject	one of two ways...
Posted by	Spee on May 18, 2006 at 12:14 PM
	This message has been viewed 47 times.
In Reply To	Mine, or will Bernie's do? posted by TT XTZ on May 18, 2006 at 12:11 PM
Message	1) you can put them in the night before, and make sure you keep your distance from the car in front of you on the way to the track. 2) if there is space at the track in the pits to get to 30mph or so, you can instal the pads there and do some bedding there. Also on the warm up lap. Later, Spencer AIM: sbsTT14 PETZ member #4 '91 300ZX TT Stage V+ '96 Jeep Cherokee Sport "also tired of ppl driving in a straight line for 1/4 mile and thinkin they're hot shit" - hey GotBo0st 22:17:26 09/26/04 "Moral of my night, fucking young people who inheret money, and dont know shit, but think they do are dumb fucks." - suprakillinz 02:37:37 07/02/05 "You are stupidier than dirt." - AzHeat 21:23:10 08/05/04 "Welcome, and I'd listen to Spee" - BigTDogg (MA) 18:21:41 02/17/04 "SCORE: Spee=1 The rest of us=0 (n/m)" - jaymztt(seWA) 19:17:12 07/23/04
Follow Ups	MSR checklist for ZCON?? - PakiHomBoy 11:41:23 05/18/06 simplified; - ni[X]it 11:48:07 05/18/06 thats exactly what i was looking for, thanks a bunch (n/m) - PakiHomBoy 11:51:05 05/18/06 Thank you! (n/m) - TT XTZ 12:00:58 05/18/06 For you long distance fellers, - ni[X]it 12:05:30 05/18/06 *fellettes (n/m) - Spee 12:08:49 05/18/06 *fellates (n/m) - Kenny 12:11:09 05/18/06 Mine, or will Bernie's do? - TT XTZ 12:11:11 05/18/06 one of two ways... - Spee 12:14:36 05/18/06 Correction; - ni[X]it 12:18:38 05/18/06 hi - zboost(tx) 12:35:22 05/18/06 The "unbed" by daily driving. Best is to bed-in as close - Scotts94z32 14:44:32 05/18/06 good point. - Spee 12:42:53 05/18/06 If you decide to install them at the track, there is not - sfarrah 12:19:27 05/18/06 Holla G/F!!! - ni[X]it 12:16:50 05/18/06 Pffft... a lot you know. She'll be putting swapping the - Dave N 12:39:25 05/18/06 she'll be doing what? (n/m) - Spee 12:45:37 05/18/06 Thanks to all for the info! - TT XTZ 12:33:49 05/18/06 how do you visually inspect wheel bearings? - ZEngineer 12:07:55 05/18/06 what, they don't do tech inspections when you break in to - Spee 12:09:58 05/18/06 Hi. - ni[X]it 12:13:07 05/18/06 no Zcooon for me - ZEngineer 12:18:45 05/18/06 Haha... - BradZ (FL) 12:20:31 05/18/06 bahaha That's great! (n/m) - ZEngineer 12:26:58 05/18/06 I can do that for you... Just give me your list. ;-) - Z-Jay (Edmonton, AB) 12:29:02 05/18/06 I've emailed you the list - ZEngineer 12:31:59 05/18/06 lift one corner at a time with tire on and off the ground... - Cap927(Boston) 12:19:12 05/18/06 I always thought that line of testing - ZEngineer 12:23:14 05/18/06 If the wheel wiggles and BJs/tie rods are tight - dogpile (still dogpile) 12:30:45 05/18/06 Thanks to Rodel for the info. - 300twinz (satx) 11:50:54 05/18/06 Is anyone bringing a jack and 2x4's? (n/m) - zboost(tx) 13:03:27 05/18/06
Post a Followup	You cannot reply to this message because you are not logged in.