Subject	brake bleeder ... yeah ... that's what it is ... right
Posted by	Guapo on May 10, 2006 at 3:34 PM
	This message has been viewed 49 times.
In Reply To	you know the fluid should look tan-ish clear, not green :P posted by CHUNG (Dallas) on May 10, 2006 at 03:32 PM
Message	Well, it claims a high temp, so I didn't know if it's legit or not. We overheated the ATE Blue stuff at Hallett, and was looking at options. Might just stick to the Motul 600 then. Petz #2 "What's the point of having the car if you don't drive it?" - Mrs. Guapo 08/20/05 Jeeeesus Christ - my Dad (after a ride in my Z) 12/26/04 YugoBernie: i dont really have anything against labree People have the right to freedom of expression. However, people also have the right to point and laugh- aliaZ 04/06/06
Follow Ups	Injector upgrade and plenum pull question. - BigTDogg (MA) 14:40:51 05/10/06 Are you going with the 95+ style injectors? - ZonaZ 14:53:20 05/10/06 Yup, gonna send the LP to JWT for machining. (n/m) - BigTDogg (MA) 14:58:29 05/10/06 Then you have to have the new fuel rails to fit the injector (n/m) - YugoBernie (NoVA) 15:00:06 05/10/06 yep (n/m) - Guapo 15:01:17 05/10/06 damn. (n/m) - CHUNG (Dallas) 15:03:15 05/10/06 you planning on doing this? (n/m) - Guapo 15:08:41 05/10/06 nope. - CHUNG (Dallas) 15:15:31 05/10/06 bah ... - Guapo 15:18:01 05/10/06 you know the fluid should look tan-ish clear, not green :P - CHUNG (Dallas) 15:32:03 05/10/06 brake bleeder ... yeah ... that's what it is ... right - Guapo 15:34:53 05/10/06 I see. Trial and error. - CHUNG (Dallas) 15:51:55 05/10/06 Re: where did you get that brake bleeder? (n/m) - Emxracer (SOCAL) 16:39:56 05/10/06 Matco tool truck and matcotools.com - CHUNG (Dallas) 16:45:39 05/10/06 I'll def have to borrow it :) (n/m) - Guapo 18:55:23 05/10/06 $1 to rent! :P - CHUNG (Dallas) 23:05:57 05/10/06 yep 2nd - ZonaZ 15:05:12 05/10/06 *new orings, rubber upper & lower isolators, fuel rail caps (n/m) - YugoBernie (NoVA) 15:21:00 05/10/06 Yeah, crap, that sucks. Thanks for the info. (n/m) - BigTDogg (MA) 15:27:45 05/10/06 yep, get's pricey fast > 1K (n/m) - ZonaZ 15:41:26 05/10/06 mmm... delish... - Joe(NoVA) 18:28:44 05/10/06 Did you have any porting done to the lower plenum - BigTDogg (MA) 18:54:08 05/10/06 You have to. The 90-93 injector seat is conical .. - Guapo 18:58:55 05/10/06 I meant where the air goes (n/m) - BigTDogg (MA) 19:14:29 05/10/06 you guys are killing me. ugh. (n/m) - ni[X]it 15:58:34 05/10/06 product<--------------------------------------------->market (n/m) - YugoBernie (NoVA) 16:03:59 05/10/06 That's pretty far. (n/m) - Z-Jay (Edmonton, AB) 18:21:25 05/10/06 :( (n/m) - Guapo 16:10:12 05/10/06 Anxious buyer ------------------------------------> (n/m) - Only1Z 20:29:46 05/10/06
Post a Followup	You cannot reply to this message because you are not logged in.