Subject	Few pics with the new drag wheels and cutouts,
Posted by	zboost(tx) on May 01, 2006 at 9:11 PM
	This message has been viewed 647 times.
Message	Got my new draglites in for the rear a while ago, but didn't get a change to hit the strip until this past Friday. Here's some pics I took. You can also my new aerocatch hoodpins ([ www.aerocatch.com ]) overall a lot less noticible than the previous ricy sparcos. And here are my cutout's which I've had for a while, but never posted pics. This is a pretty good location for them as well. They are modified "jegs" brand, off of jegs.com I ordered 2.5" cutouts, but they were really 2.25", so I basically took them to my local muffler shop and had them only use the cutout part with the cap, and weld them to the sides of the testpipes, so they wouldn't interfere with my regualr exhaust and be a restriction. I sprayed some aluminum paint as well, so they wouldn't rust. Now on eBay!! click the pic below! BEST 1/4mile 11.92 @ 117mph. PUMP gas, true 11 sec. street car :) stock turbos/injectors "yo yo. writing this one in jail - tight300zx" I hope you got soap on a rope?? (n/m) - Spongerider :) 19:14:08 04/01/04 we'll know if the screen name changes ;) (n/m) - SactoTodd 19:32:36 04/01/04 "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - - DC 21:11:01 02/18/04 (the "holes" were located on the exhaust)
Follow Ups	Few pics with the new drag wheels and cutouts, - zboost(tx) 21:11:37 05/01/06 Oh hell, LOOK OUT! =P have fun with them... (n/m) - Patrick(Austin) 21:13:39 05/01/06 this is an eletronic controlled cut-out right? interesting (n/m) - Max865(ATL) 21:17:55 05/01/06 Looks like he just uses block-off plates for the street... - BradZ (FL) 21:19:22 05/01/06 haha - Max865(ATL) 21:26:38 05/01/06 nope, manual screw on type. - zboost(tx) 21:20:55 05/01/06 they do go bad in short amount of time - Max865(ATL) 21:28:13 05/01/06 yea... and about $360 for the pair! - zboost(tx) 21:37:22 05/01/06 Re: yea... and about $360 for the pair! - M.U.L.E. 09:25:28 05/02/06 That's gonna understeer like a mofo! :P - BradZ (FL) 21:22:52 05/01/06 i bet she sounds mean. (n/m) - Medlin1(SWMO) 21:26:30 05/01/06 You have no idea.....lol - zboost(tx) 21:35:00 05/01/06 Really? Mine sounded like shat with just my downpipes. (n/m) - Unluky (MO) 23:28:56 05/01/06 I learned something new today! - TT XTZ 21:41:14 05/01/06 Glad I could help (n/m) - zboost(tx) 22:12:04 05/01/06 awesome looks good. I got some cutouts I ordered from - CollegeBoy 22:25:41 05/01/06 Sweet, did you get the ones like mine as well? - zboost(tx) 22:29:33 05/01/06 Supposedly they'll last..only time will tell. Here they are - CollegeBoy 22:40:26 05/01/06 Where are you going to mount them? - zboost(tx) 22:45:10 05/01/06 I'll find out when then I do the engine work. - CollegeBoy 22:51:11 05/01/06 Not worried about hot exhaust cooking the trans? (n/m) - YugoBernie (NoVA) 01:13:09 05/02/06 Not really - zboost(tx) 09:14:03 05/02/06 Have you dyno'ed with them capped and then open? (n/m) - SactoTodd 09:21:10 05/02/06 Not yet........but - zboost(tx) 09:27:29 05/02/06 Re: Not yet........but - M.U.L.E. 09:32:17 05/02/06 I picked up 4mph at the drag strip taking my - dream Z (MD) 09:56:43 05/02/06 Depends on your exhaust set-up (i.e. cats, bends, etc.) (n/m) - Scotts94z32 11:13:45 05/02/06 Better yet, skip the dyno - RSR 11:03:07 05/02/06 agreed. (n/m) - sfarrah 15:55:26 05/02/06 If he had an auto, that could be a valid suggestion - Zyal8r (Dallas) 16:09:04 05/02/06 This goes to the reasoning for modifying. - RSR 08:12:41 05/03/06 bad idea... - Spee 18:10:38 05/02/06 bah (n/m) - RSR 08:18:50 05/03/06 Already done......results>> - zboost(tx) 18:30:10 05/02/06 This is easy. - RSR 08:16:58 05/03/06
Post a Followup	You cannot reply to this message because you are not logged in.