Subject	Measure 4 times, cut once but serously..
Posted by	Spectrum (WI) on April 18, 2006 at 11:47 PM
	This message has been viewed 39 times.
In Reply To	Rear STB question posted by EMTP2700 on April 18, 2006 at 11:40 PM
Message	What I did is use some blue 1.5" wide tape and taped the area I wanted to cut, Basically one piece of tape. That is how I got the cuts parellel to each other. Then once I fitted one side I copied the other side by duplicating the process. To make sure they line up with each other I extended the lines with more tape so I can extrapolate where that cut line would go on the other piece. The width of cut was about 1.75" wide, I had to put a second piece of tape down to get the width right, just make sure you are parellel when applying the tape. When cutting ALWAYS drill your corners first so you have a nice radius for the black hose trim. I used a 3/8" but on the corners.
Follow Ups	Carbing STB Install - Spectrum (WI) 23:24:47 04/18/06 Very nice, good pics. (n/m) - manstretch (NC) 23:29:53 04/18/06 Engine bay stuff is not finished yet but close>> - Spectrum (WI) 23:32:12 04/18/06 Question - Cincyzx 23:50:31 04/18/06 I am not sure I understand your question, do you mean - Spectrum (WI) 23:53:53 04/18/06 Oh sorry :) that was a bit vague... - Cincyzx 23:55:44 04/18/06 Did everything with a spray car believe it or not, do this.. - Spectrum (WI) 00:09:27 04/19/06 Spray Can,,, typo oops (n/m) - Spectrum (WI) 00:11:18 04/19/06 clean! (n/m) - Guapo 23:30:23 04/18/06 Very nice, - Ebola (Moving to Edmonton) 23:34:23 04/18/06 Trust me Stereo Plans is not the proper word.. - Spectrum (WI) 23:38:25 04/18/06 Should have guessed something like that - Ebola (Moving to Edmonton) 23:42:25 04/18/06 I need to finish my T-top bracket so they fit in there, - Spectrum (WI) 23:50:40 04/18/06 What is that lining the cut out part at the rear bar? - TBlakeZ (NorCal) 23:39:43 04/18/06 1/8" ID vacuum hose (truevalue @ .27 cents/ft) (n/m) - Spectrum (WI) 23:41:33 04/18/06 Rear STB question - EMTP2700 23:40:57 04/18/06 Measure 4 times, cut once but serously.. - Spectrum (WI) 23:47:27 04/18/06 Re: Measure 4 times, cut once but serously.. - EMTP2700 00:13:35 04/19/06 Couple more things when measuring.. - Spectrum (WI) 00:27:40 04/19/06 Re: Couple more things when measuring.. - EMTP2700 01:24:45 04/19/06 some nice fine touch and clean Z! (n/m) - CHUNG (Dallas) 23:42:39 04/18/06 very clean install on the rear...looks great! (n/m) - LoweBudget(Louisa VA) 23:58:08 04/18/06 Very clean install - Z32BOY(SoCal) 00:18:56 04/19/06 Nice but your fuel lines are far too short. (n/m) - YugoBernie (NoVA) 00:22:48 04/19/06 How much "slack" is necessary?? - Spectrum (WI) 00:31:08 04/19/06 The stock lenght is 14" or so as I recall. (n/m) - YugoBernie (NoVA) 00:40:48 04/19/06 If that is the case then I can run it around like the - Spectrum (WI) 00:44:33 04/19/06 Whatever you do they need to have enough slack to account - YugoBernie (NoVA) 00:54:13 04/19/06 another way I relate to the Z so well. (n/m) - Spee 00:44:50 04/19/06 lol (n/m) - 300zxquire 00:55:04 04/19/06 I call bluff--for you are HALF white. (n/m) - Fuzznutz 05:01:13 04/19/06 You bring up a very good point my friend. Also, I think he - 300zxquire 11:41:43 04/19/06 correct... - Spee 20:40:39 04/19/06 lol (n/m) - Fuzznutz 20:45:59 04/19/06 VERY NICE!~ I want to eat tonights dinner off that engine. - Shawn300zTT GT28R MD 00:25:00 04/19/06 I want your plenums (n/m) - JayT 00:42:01 04/19/06 Silver Powdercoat an extra coat of clear on top. (n/m) - Spectrum (WI) 00:46:04 04/19/06 I thought it was a very clean stock plenum.. - Shawn300zTT GT28R MD 03:00:40 04/19/06 sexy (n/m) - rufflez 01:08:25 04/19/06 very cool - maglito 03:12:30 04/19/06
Post a Followup	You cannot reply to this message because you are not logged in.