Subject	not really, I got those off the SCC site...
Posted by	Zeus on February 21, 2006 at 9:23 PM
	This message has been viewed 52 times.
In Reply To	Do you have a before and after of this... posted by Patrick(Austin) on February 21, 2006 at 09:10 PM
Message	However, just imagine this....in the before picture, you'd be able to see less than half of that all the way through..it's that bad in there. Blocks from the factory almost always have horrible casting flash. ----------------------------------------------------------- Zeus: "I just installed my first piston. It was like losing my virginity all over again. I wasn't sure what I was doing and it was over all too quickly".
Follow Ups	Help with piston selection > - whitepearlz 16:56:50 02/21/06 Any of those pistons will work just fine. - Ash's Z 17:10:16 02/21/06 check your bellsouth email.................. (n/m) - Southern-Z (Little Rock) 17:34:36 02/21/06 My non professional opinion - SactoTodd 17:17:36 02/21/06 Your stock rods will be fine with your setup... - Zeus 17:18:55 02/21/06 That short skirt really shows of your nice rod!!1one (n/m) - SactoTodd 17:22:13 02/21/06 lol...maybe so, but you looked ;) (n/m) - Zeus 17:23:54 02/21/06 Also, fwiw,CPs come with new wrist pins and rings (n/m) - Zeus 17:34:58 02/21/06 Re: Also, fwiw,CPs come with new wrist pins and rings - Mitchell(AMZ Performance) 17:40:32 02/21/06 They did when I got them from Kyle when he was at SGP (n/m) - Zeus 17:42:23 02/21/06 Re: They did when I got them from Kyle when he was at SGP (n - Mitchell(AMZ Performance) 17:44:28 02/21/06 It looks like Kyle has them listed on his IPP site - the - whitepearlz 17:46:02 02/21/06 Re: It looks like Kyle has them listed on his IPP site - the - Mitchell(AMZ Performance) 17:47:38 02/21/06 Yup, that's the going rate for those with pins and rings. (n/m) - Zeus 17:49:48 02/21/06 I know you very recently had your shortblock rebuilt > - whitepearlz 18:01:10 02/21/06 Re: I know you very recently had your shortblock rebuilt > - Zeus 18:12:23 02/21/06 When you mention Clevite77 bearings, I'm assuming - whitepearlz 18:29:03 02/21/06 Not a problem, that's what we're here for =) - Zeus 18:44:01 02/21/06 Thank you, I truly appreciate it. It seems as if - whitepearlz 18:53:29 02/21/06 Yup, aluminum oxide stones in different shapes and lengths - Zeus 19:03:00 02/21/06 Wow, thanks a TON. None of my searching brought up pictures - whitepearlz 19:17:00 02/21/06 my pleasure (n/m) - Zeus 21:10:21 02/21/06 Do you have a before and after of this... - Patrick(Austin) 21:10:53 02/21/06 not really, I got those off the SCC site... - Zeus 21:23:35 02/21/06 mine are 89mm coated wisecos. they seem to be holding up - 700hpz1zx 17:43:29 02/21/06 Why would you go with different pistons? - Shawn300zTT GT28R MD 03:35:16 02/22/06 Why dont you go with these.... - Patrick(Austin) 18:05:57 02/21/06 Here is some add info... - Patrick(Austin) 18:16:19 02/21/06 Engine out again? Sorry to hear it. Seems like the other - zmenon 18:10:20 02/21/06 Ross pistons are pretty sweet, or so I'm told. . .:) (n/m) - Rule12b 18:24:08 02/21/06 Hijack - Still going to Zcon? (n/m) - zgene4 21:35:32 02/21/06
Post a Followup	You cannot reply to this message because you are not logged in.