Subject	Those look familiar... What you'd have to do is get a flat
Posted by	whitepearlz on February 16, 2006 at 12:07 PM
	This message has been viewed 31 times.
In Reply To	the holes are pretty big from the flanges... posted by Atl300zxTT on February 16, 2006 at 12:02 PM
Message	disc of aluminum (or steel), cut a 1/2"-3/4" hole in the center, and a have a similarly I.D.-sized section of pipe welded on each. You could then attach the two with a rubber hose which would allow for the bends it would have to make. "bJammmin: holy jesus fucking shit bJammmin: people who say money cant buy happiness, obviously havn't driven a twin turbo Z" "done"? BAHAHAHAHAH ... it's never "done" ...." (in regards to the Z) Posted by: Guapo on June 16, 2005 at 10:34 PM WINTER (Also known as a "WISCONSIN WINTER") This is one of Wisconsin's two seasons which lasts approximately 9 months. The other season is the ROAD CONSTRUCTION season, lasting roughly 3 months.
Follow Ups	Blow off Valve Position Debate - Atl300zxTT 10:50:40 02/16/06 Old school HKS and Blitz had them on the outer pipes (n/m) - sfpearl300zTT 10:56:43 02/16/06 The primary job of BOV's is to release the pressurized air - Guapo 10:57:59 02/16/06 That's how I understood it and tried to explain it also. - Scotts94z32 11:08:50 02/16/06 More room on the outer pipes, easier to fit. Especially if - speedr300z (ATL) 11:15:47 02/16/06 tell me if what i am saying is correct.... - Atl300zxTT 11:51:39 02/16/06 that is the way I understand it, but I have not done the - Guapo 12:06:00 02/16/06 Re: tell me if what i am saying is correct.... - Kenny 12:08:14 02/16/06 thanks for the answers...this actually clears up a lot of my - Atl300zxTT 12:17:16 02/16/06 good explanation. Hopefully this post comes up in - Waco300zx 12:45:03 02/16/06 but reversion would imply a "flow" - Spee 13:00:01 02/16/06 Re: but reversion would imply a "flow" - Kenny 13:12:23 02/16/06 Can't argue with the bold argument :-) (n/m) - Joe(NoVA) 13:28:34 02/16/06 That makes sense except for one part. - 300zx90 (CO) 12:27:19 02/16/06 Re: That makes sense except for one part. - Kenny 12:44:58 02/16/06 Now we're getting close - 300zx90 (CO) 14:00:56 02/16/06 Closer to throttle = better. End of Story. (n/m) - Kenny 11:00:11 02/16/06 this means nothing without justification (n/m) - Atl300zxTT 11:26:38 02/16/06 Think about it. Also see Guapo's reply. (n/m) - Woody75 (Denver) 11:31:49 02/16/06 Have you tried searching? - Kenny 11:32:33 02/16/06 Search? This website has a Search Function? - Atl300zxTT 11:45:34 02/16/06 Yes, try using it. - Kenny 11:52:18 02/16/06 Re: Yes, try using it. - Atl300zxTT 12:14:07 02/16/06 actually, this was first discussed back in 2000 summer - CHUNG (Dallas) 21:20:24 02/16/06 Closer to the TB = better. This is the only reason I - whitepearlz 11:09:40 02/16/06 On this same note... - whitepearlz 11:22:39 02/16/06 you could probably fab a balance line in their place (n/m) - Guapo 11:29:21 02/16/06 the holes are pretty big from the flanges... - Atl300zxTT 12:02:36 02/16/06 Those look familiar... What you'd have to do is get a flat - whitepearlz 12:07:56 02/16/06 big balance tube :) (n/m) - Guapo 12:09:59 02/16/06 bigger is better :) (n/m) - Atl300zxTT 12:15:17 02/16/06 I put mine before the intercooler, about 2' from the turbo. - Ash's Z 11:57:19 02/16/06 interesting (n/m) - red300zxtt 12:03:55 02/16/06 got pics? - aliaZ 12:06:42 02/16/06 thats like asking a butcher if he's got a steak.. - Spee 12:10:37 02/16/06 Or, like asking if Spee has personality. - Ash's Z 12:18:06 02/16/06 Re: got pics? - Ash's Z 12:16:54 02/16/06 FWIW, if you ask "well, why did nissan put it before the - Ash's Z 12:15:58 02/16/06 *....didn't put it before...* (n/m) - Ash's Z 12:19:21 02/16/06 "a logistical nightmare to implement that way" - Kenny 12:23:15 02/16/06 Right? :) (n/m) - Ash's Z 12:30:05 02/16/06 Re: I put mine before the intercooler, about 2' from the tur - Kenny 12:20:44 02/16/06 FWIW, on Dee's car when we were datalogging the temps - Ash's Z 12:29:30 02/16/06 Wow. - Kenny 12:34:15 02/16/06 see this post was worth something :) (n/m) - Atl300zxTT 12:38:14 02/16/06 yes, this is post of the day (n/m) - mousersix (San Antonio) 12:40:18 02/16/06 I know =). - Kenny 12:46:43 02/16/06 Let me check your post history....ummmm.....not a chance in - Atl300zxTT 12:49:46 02/16/06 Yes you can vent from anywhere in the system, however as you - 300zx90 (CO) 12:32:14 02/16/06 Related question on BOV/Recirc engagement... - mousersix (San Antonio) 12:39:48 02/16/06 As seen here... - mousersix (San Antonio) 12:43:34 02/16/06 That was just a convenient location to hook mine up - Ash's Z 12:48:05 02/16/06 thanks for the info (n/m) - mousersix (San Antonio) 13:13:22 02/16/06 question? how are the intake and IC tubing so slow in that - SpecNATT (Houston) 19:25:18 02/16/06 A BOV works on a pressure differential, not just manifold - Ash's Z 12:44:30 02/16/06 I'm having a hard time believing there will be no effects - mousersix (San Antonio) 13:12:00 02/16/06 I would have a hard time believing it too. :) - Ash's Z 13:22:38 02/16/06 thanks Ash - mousersix (San Antonio) 13:46:33 02/16/06 Mine is after the IC, close to the TB - F8IZHIS 12:59:58 02/16/06 Bee-Emm-Dub!! What? Yeaaaaah!! OK!!! (n/m) - Waco300zx 13:01:50 02/16/06 BEEIMDABOWLYOU and VEEDABOWLYOU TOO! (n/m) - Ash's Z 18:28:59 02/16/06 Know what the difference between a porcupine and a BMW is? - Ash's Z 13:24:32 02/16/06 Ouch... - F8IZHIS 13:43:46 02/16/06 XP SP2 - Ash's Z 13:51:47 02/16/06 No offense taken - F8IZHIS 14:17:39 02/16/06 I use the standby function with XP. WHen I turn the car - Ash's Z 14:45:46 02/16/06 Absolute classic Ash. BTW where did you get the - Riddick 14:40:42 02/16/06 www.summitracing.com. It is all 6AN braided hose and - Ash's Z 14:43:35 02/16/06 Thanks Ash. Nice work..... (n/m) - Riddick 17:43:43 02/16/06 you've never heard that one before? - Spee 14:50:51 02/16/06 For a guy who really hasn't done "Dick" to his Z - Riddick 17:43:01 02/16/06 lol, nice try n00b. - Kenny 17:51:41 02/16/06 thigh* (n/m) - ZXRider(SoCal) 19:42:28 02/16/06 He might be a good mechanic but he is an ass and - Riddick 08:03:20 02/17/06 too* - Atl300zxTT 09:38:19 02/17/06 Thanks for the grammatical lesson jag-off. - Riddick 10:29:01 02/17/06 Noob = new to this site (n/m) - Atl300zxTT 11:37:43 02/17/06 Joined March 4th 2004. Been reading on this site - Riddick 12:09:36 02/17/06 LOL. WTF are you talking about? - Spee 23:16:44 02/16/06 First off I am not a dumb fuck Noob little guy. - Riddick 08:01:29 02/17/06 BOV's are bad for most VG30DETT. (n/m) - Spongerider :) 13:23:57 02/16/06 bad? - Max865(ATL) 16:24:48 02/16/06 Bad from a performance point. (n/m) - Spongerider :) 18:30:13 02/16/06 Dean, would you mind explaining a little more? - Ash's Z 18:44:19 02/16/06 Sure and I know you know too. - Spongerider :) 20:13:05 02/16/06 Well, there isn't anything additional that needs to be done - Ash's Z 21:45:23 02/16/06 Well as usual we don't see eye to eye when it comes to - Spongerider :) 22:52:16 02/16/06 Well, there's nothing wrong with that. - Ash's Z 13:22:37 02/17/06 I use my Greddy E-manage to compensate for the - Riddick 10:47:01 02/17/06 Re: I use my Greddy E-manage to compensate for the - Spongerider :) 10:59:30 02/17/06 Thank you. I thought that's what you meant. - Riddick 12:11:22 02/17/06
Post a Followup	You cannot reply to this message because you are not logged in.