Subject	I went to a shop and they ended up
Posted by	sfpearl300zTT on January 12, 2006 at 7:22 PM
	This message has been viewed 48 times.
In Reply To	Question about roll fenders... posted by TheTwinZ (Peru) on January 12, 2006 at 05:36 PM
Message	Cutting out the inner fender lip. They were originally going to roll it, with a special machine they had, but they said it would have taken hours to do it right, and it was cheaper and simpler to cut them away, as well as more effective since there is no fender at all to rub against, rather than have the fender pushed back a little bit. Turned out great, and no significant loss of integrity of the wheel well. It had to be done to fit my 275 yokohomas on the rear when I got new tires. I can take pics in the day light if needed tomorrow. ------------------------------------------------------------ bJammmin: i was thinking about masking off the bottom part (black on your lip) and painting mine flat black, caus it'll just keep getting scuffed forever sfpearl300z: thats half the reason why i did it to mine sfpearl300z: dont have to worry about any imperfections sfpearl300z: cause it gets so much abuse bJammmin: yeah dude so true goddamn bJammmin: why are you a fucking genius sfpearl300z: lol sfpearl300z: you know what i hate? bJammmin: whats dat yo sfpearl300z: being so damn smart bJammmin: LOL sfpearl300z: i actually dont look too far into the lives of people on the forums sfpearl300z: dont pay close enough attention WickedPuddle: see WickedPuddle: thats where you and i are different WickedPuddle: i am on a whole different level of having no life MiCHaeLkiH: i forked out 650 for my vibrating one
Follow Ups	Question about roll fenders... - TheTwinZ (Peru) 17:36:10 01/12/06 I haven't had the need, but know of some that have used a - Governor 17:39:56 01/12/06 I used the handle for my floor jack wrapped in a rag. - sfarrah 17:42:13 01/12/06 2nd governor on the bat - BigTDogg (MA) 17:42:54 01/12/06 Re: Question about roll fenders... - wild300 17:43:08 01/12/06 car jack + bat = rolled fender, maybe add some heat - Smitytec 17:46:35 01/12/06 I used a baseball bat - AzHeat 17:47:04 01/12/06 Or you could just order this and do it the right way. - twinturbineZ 17:59:19 01/12/06 if both tools yield the same result, why is that one "right" - mousersix (San Antonio) 18:02:47 01/12/06 Reading comprehension owns you - twinturbineZ 18:15:14 01/12/06 man, I got pwned, I apologize for my stupidity - mousersix (San Antonio) 18:20:59 01/12/06 example: - mousersix (San Antonio) 18:21:38 01/12/06 If professionals can crack your paint what makes you - AzHeat 18:26:40 01/12/06 Ask the average joes using it - twinturbineZ 18:30:47 01/12/06 It doesn't say they didn't have cracked paint in those - AzHeat 18:54:20 01/12/06 what? I wasn't even talking about that - mousersix (San Antonio) 18:31:23 01/12/06 Since you've never used this tool, how can you say it has - twinturbineZ 18:35:51 01/12/06 have you used that tool before? - dogpile 18:41:18 01/12/06 Do some research on Eastwood before you run your mouth - twinturbineZ 19:03:50 01/12/06 right. so youre dumb. gotcha (n/m) - dogpile 20:07:58 01/12/06 no, you got told. (n/m) - mousersix (San Antonio) 20:25:39 01/12/06 :( that's cause i didn't know what i was dealing with (n/m) - dogpile 21:00:01 01/12/06 nice job sidestepping the entire post. (n/m) - mousersix (San Antonio) 20:30:11 01/12/06 because I know people have rolled their fenders - mousersix (San Antonio) 18:41:22 01/12/06 You can do it either way, however the roller tool - twinturbineZ 19:05:09 01/12/06 How so? I missed the comparative analysis. (n/m) - mattztt 20:00:27 01/12/06 sorry I meant to respond to twinturbineZ (n/m) - AzHeat 18:50:16 01/12/06 That doesn't ensure no cracks will happen in older paint - Zster (Big Red) 14:34:11 01/13/06 A lot of money for something you will only use once. (n/m) - AzHeat 18:03:55 01/12/06 Not if does the job right and doesn't mar the finish - twinturbineZ 18:17:19 01/12/06 $250 is hardly minimal unless your are Bill Gates. (n/m) - AzHeat 18:22:05 01/12/06 ... - CarbonZTT 18:57:46 01/12/06 good luck finding a buyer . I like the "Free" option - AzHeat 19:07:08 01/12/06 i have that. and i cracked the paint on my red car - Z32POWER.com 18:19:10 01/12/06 I took mine to a PROFESSIONAL shop and they couldn't do it - Scotts94z32 18:08:31 01/12/06 Your guys sucked. (n/m) - Guapo 18:26:12 01/12/06 I went to a shop and they ended up - sfpearl300zTT 19:22:34 01/12/06 Thanks a lot, guys! I'm gonna use a bat or something similar - TheTwinZ (Peru) 21:11:48 01/12/06 Prime and paint the inner fender well portion - WildBillZx 01:07:50 01/13/06 Thanks! I'll do that too. (n/m) - TheTwinZ (Peru) 01:28:19 01/13/06 my body shop heated the inside/outside fender lightly - RedSER13 01:15:51 01/13/06 some pictures would be nice (n/m) - Max865(ATL) 14:42:11 01/13/06 here: - RedSER13 01:46:04 01/15/06 The Eastwood tool works very well, some guys locally - kandy2dr 15:36:22 01/14/06
Post a Followup	You cannot reply to this message because you are not logged in.