Subject	Two different issues.
Posted by	Guapo on January 12, 2006 at 12:03 PM
	This message has been viewed 34 times.
In Reply To	I was actually talking about the gauge itself. El Guapo posted by Scotts94z32 on January 12, 2006 at 11:57 AM
Message	The Blitz has two ways of setting boost, only one of which applies to a TT setup. You set your boost ratio in points 0-100. In auto mode (not for TT setups), you set your boost level to the single psi. The readout on the gauge shows to the tenth psi. In either case, the sig figs on the readout are irrelevant to the margin of error on the setting. Petz #2 "What's the point of having the car if you don't drive it?" - Mrs. Guapo 08/20/05 Jeeeesus Christ - my Dad (after a ride in my Z) 12/26/04 YugoBernie: i dont really have anything against labree
Follow Ups	Bar vs kg/cm^2 vs psi etc..... - Joe(NoVA) 09:29:29 01/12/06 :D - BigTDogg (MA) 09:41:22 01/12/06 Different 'stokes' for different folks......... (n/m) - 240Z FeO2 10:04:32 01/12/06 Tony likes to see big numbers - ZEngineer 10:08:41 01/12/06 haha. For some really big nos., how about using nanometers? (n/m) - 240Z FeO2 10:22:30 01/12/06 No Planck lengths, no care. (n/m) - Kenny 10:25:35 01/12/06 I prefer to use angstroms actually. Expwnents :) (n/m) - BigTDogg (MA) 10:41:36 01/12/06 For a bigger # than 32.2 ft H20 use feet of air ;) (n/m) - ZUL8TR 11:12:59 01/12/06 how do you say it? "foot waters"? (n/m) - mousersix (San Antonio) 12:11:09 01/12/06 Feet of water, like Milimeters of Mercury (n/m) - BigTDogg (MA) 12:35:56 01/12/06 ah, sweet :) (n/m) - mousersix (San Antonio) 20:24:40 01/12/06 That's nice... - Kenny 09:57:16 01/12/06 "most boost controllers vary +/- 2 psi" - ZEngineer 10:02:00 01/12/06 I didn't say electronic controllers. - Kenny 10:14:57 01/12/06 Ok, people are thinking two different things here. You are - Z-Jay (Edmonton, AB) 10:27:48 01/12/06 if the accuracy was really +/-2psi, why would Blitz(example) - ZEngineer 10:42:48 01/12/06 my blitz reads to 0.1 psi (n/m) - Guapo 10:45:13 01/12/06 that further proves the point that +-2psi doesn't make sense (n/m) - ZEngineer 10:49:53 01/12/06 Did you even read my post? - Kenny 10:53:21 01/12/06 If it takes it to 0.000001, it has nothing to do with - Guapo 11:02:59 01/12/06 Significant figures implies differently... (n/m) - Scotts94z32 11:20:12 01/12/06 I can't believe you guys aren't getting this. - Kenny 11:25:08 01/12/06 I was actually talking about the gauge itself. El Guapo - Scotts94z32 11:57:36 01/12/06 Two different issues. - Guapo 12:03:23 01/12/06 Now I'm clear on what you meant - ZEngineer 12:07:50 01/12/06 There we go. - Kenny 12:16:50 01/12/06 How well it controls to a setpoint is a totally different - Z-Jay (Edmonton, AB) 11:13:00 01/12/06 Exactly. - Kenny 11:15:33 01/12/06 You helped me interpret something correctly in this thread - ZEngineer 12:18:01 01/12/06 Re: You helped me interpret something correctly in this thre - Kenny 12:21:47 01/12/06 I appreciate the warning, I'll start working on a rebuttle - ZEngineer 12:26:31 01/12/06 Yeah, that's why i prefaced the last paragraph - Joe(NoVA) 10:03:19 01/12/06 Indeed =). (n/m) - Kenny 10:10:53 01/12/06 Cool deal Joe, and thanks for the clarification! (n/m) - Ash's Z 12:37:28 01/12/06
Post a Followup	You cannot reply to this message because you are not logged in.