Subject	Yeah, I don't have a dyno out here
Posted by	wilkendw on January 05, 2006 at 12:07 AM
	This message has been viewed 19 times.
In Reply To	Re: Re: Why did your engine blow up last time. posted by dream Z (MD) on January 04, 2006 at 11:27 AM
Message	and my pump gas is only 91, and when I blew the engine it was at about 5000 ft elevation. Maybe I'm going to need an AFC too so I can tweek my fuel map. You have 93 on the east coast I think... If I try to run anything over 14 I detonate at 14 btdc.
Follow Ups	Rebuild Opinions please... - wilkendw 02:01:48 01/04/06 Why did your engine blow up last time. (n/m) - dream Z (MD) 02:09:44 01/04/06 Re: Why did your engine blow up last time. - wilkendw 05:34:44 01/04/06 Re: Re: Why did your engine blow up last time. - dream Z (MD) 11:27:23 01/04/06 Yeah, I don't have a dyno out here - wilkendw 00:07:48 01/05/06 I would recommend some water/methanol injection - Shawn300zTT GT28R MD 02:31:36 01/04/06 Re: I would recommend some water/methanol injection - dream Z (MD) 02:33:16 01/04/06 #4, since nobody else is suggesting... - canyoncarver 08:37:03 01/04/06 Forged pistons don't really melt at a higher temp, also - Scotts94z32 09:37:09 01/04/06 I was curious........ ^^^ - canyoncarver 14:11:17 01/04/06 Stronger, yes, higher T(m), no. What is the basis for your - Scotts94z32 15:05:34 01/04/06 I didnt think a cast iron block had sleeves? (n/m) - 90zilverTT 10:32:27 01/04/06 Re: I didnt think a cast iron block had sleeves? - dream Z (MD) 11:28:35 01/04/06 Whatever you do have the work done by a "Z" shop. Z1, SGP... (n/m) - 300zxquire 11:17:04 01/04/06 Re: Whatever you do have the work done by a "Z" shop. Z1, SGP... - dream Z (MD) 11:29:43 01/04/06 *cough* IPP > SGP *cough*....LOL..... (n/m) - Kyle(Houston) 11:30:59 01/04/06 Re: *cough* IPP > SGP *cough*....LOL..... - dream Z (MD) 11:37:04 01/04/06 Kyle: How are you handling engine-building services now? - Scotts94z32 11:52:13 01/04/06 Response for both dream Z and Scotts94z32 - Kyle(Houston) 13:24:06 01/04/06 Everything happens for a reason. (n/m) - 300zxquire 13:31:13 01/04/06 Here you go Scott-----> - Kyle(Houston) 13:34:17 01/04/06 Bring a truck up and get some cores and the diff :) (n/m) - Woody75 (Denver) 13:38:15 01/04/06 Thanks for the info, and good luck with parts and services. (n/m) - Scotts94z32 14:13:07 01/04/06 Re: Response for both dream Z and Scotts94z32 - dream Z (MD) 15:21:40 01/04/06 Sorry Kyle I forgot that you have your own place now. (n/m) - 300zxquire 13:26:25 01/04/06 Uhhh...be careful with your recommendations. - Only1Z 20:39:04 01/04/06
Post a Followup	You cannot reply to this message because you are not logged in.