Subject	Good Post, However Nissan has been racing.
Posted by	Turnerscasa (Dallas) on November 27, 2005 at 1:23 PM
	This message has been viewed 59 times.
In Reply To	I've done it, but but with compatible connectors posted by z32ttvert (MWS Motorsports) on November 27, 2005 at 12:19 PM
Message	That means some engineer probably overseas has addressed this issue. They can not run a GT car with these kinds of connectors. I will research this further to address this. Im not sure if Im being understood here. My intention with this style of connector (ITS MALE/FEMALE) was to replace what I can with them. Ill go ahead and contact the harness builder to discover the answers to the later questions regarding the sensors. I assure you it is something that can be done. Current "Z" 1994 300ZX TT 5,Speed (Pearl) 2003 G35 Sedan (White) Past "Z cars" 1991 300ZX TT 5, Speed (Red) 1990 300ZX 5, Speed NA (Red)
Follow Ups	Possible steps to make your harness BULIT PROOF! - Turnerscasa (Dallas) 09:51:29 11/27/05 Interesting! I have also been thinking about replacing - MidLifeZ 09:58:42 11/27/05 They make all sorts of sleeving, you can make it to resist - Turnerscasa (Dallas) 10:09:57 11/27/05 That would be great and all, but how would you propose - whitepearlz 10:03:35 11/27/05 I think you're right - aliaZ 10:09:21 11/27/05 I have been think a vented hood would make a huge - Ricerdaddy 10:18:54 11/27/05 I have an escort hood and DD main everywhere.>> - zboost(tx) 12:14:22 11/27/05 hard wire (solder) and then move the connector - TARGETZ 11:30:42 11/27/05 good luck - aliaZ 10:07:16 11/27/05 Considered your point. Most of what I will call proprietary - Turnerscasa (Dallas) 10:19:10 11/27/05 I've done it, but but with compatible connectors - z32ttvert (MWS Motorsports) 12:19:10 11/27/05 Good Post, However Nissan has been racing. - Turnerscasa (Dallas) 13:23:28 11/27/05 I don't think you understood what Michael (MWS) is saying - JokerF15 (NyxMotorsports) 14:08:53 11/27/05 Same connectors I used at my last job making - Shawn300zTT GT28R MD 15:47:18 11/27/05 I guess I need to add. This is a current connector - Turnerscasa (Dallas) 16:48:09 11/27/05 The ones I was using were Military grade, very top notch. (n/m) - Shawn300zTT GT28R MD 18:21:44 11/27/05 Whenever I have the chance - Spddracer 16:41:28 11/27/05 You should post a cross reference chart. - Turnerscasa (Dallas) 17:03:38 11/27/05 Try the macro setting (n/m) - EricTTZ 20:57:51 11/27/05 Try the macro setting (n/m) - EricTTZ 20:58:14 11/27/05 you had to splice in the new plugs correct? (n/m) - Max865(ATL) 22:51:32 11/27/05 Re: you had to splice in the new plugs correct? - Spddracer 06:30:45 11/28/05 i play with them all day long at work. had a bag full - Halo Z 20:13:18 11/27/05
Post a Followup	You cannot reply to this message because you are not logged in.