TwinTurbo.NET: Nissan 300ZX forum - you can buy eurathane remover which is used to strip
Subject
you can buy eurathane remover which is used to strip
Posted by
AzHeat
on November 23, 2005 at 4:34 PM
This message has been viewed
21
times.
In Reply To
Getting melted plastic off the exhaust system...
posted by BradZ (FL)
on November 23, 2005 at 11:00 AM
Message
laminated cabinets. Nasty stuff. A wire wheel would be much easier.
Follow Ups
Getting melted plastic off the exhaust system...
-
BradZ (FL)
11:00:29 11/23/05
Usually you just have to wait for it to burn off. (n/m)
-
YugoBernie (NoVA)
11:02:13 11/23/05
Yeah, I guess so...
-
BradZ (FL)
11:05:05 11/23/05
Maybe get the exhaust slightly warm with a heat gun..
-
Audioquest
15:02:37 11/23/05
you can try...
-
SkiFly01
11:16:44 11/23/05
Why didn't I think of that? Thanks Kai. (n/m)
-
BradZ (FL)
11:23:01 11/23/05
Do a couple WOT runs and it should burn off. (n/m)
-
zboost(tx)
11:28:10 11/23/05
I do several of those every day. (n/m)
-
BradZ (FL)
11:34:14 11/23/05
UGH, that is a terrible smell!
-
TT XTZ
11:44:07 11/23/05
Yeah, I always make sure I dodge 'em too...
-
BradZ (FL)
11:49:01 11/23/05
propane torch and a scraper (n/m)
-
Guapo
11:44:54 11/23/05
funny story about that
-
Moxie
12:08:34 11/23/05
hahahaha....I'll have to remember that one (n/m)
-
just4kinks
12:21:46 11/23/05
that is a good story (n/m)
-
Atl300zxTT (Less Lazy)
12:23:24 11/23/05
Nice.
-
TT XTZ
12:34:34 11/23/05
Maybe some steel wool? (n/m)
-
BigTDogg (MA)
12:24:35 11/23/05
Yeah...I'll try that...
-
BradZ (FL)
12:55:34 11/23/05
i remember those days....
-
musky
12:44:36 11/23/05
this was supposed to go under moxie's post, sorry (n/m)
-
musky
12:45:55 11/23/05
plastic or brass wheel brush on a dremel or drill. (n/m)
-
AzHeat
12:57:22 11/23/05
melt it off again (n/m)
-
BoostLesZ
13:21:21 11/23/05
would goo gone or some kind of mineral oil work?
-
Island^View
13:37:02 11/23/05
Good point, it IS plastic - maybe something like
-
TT XTZ
13:52:27 11/23/05
That's what I was wondering if anyone would suggest...
-
BradZ (FL)
13:52:48 11/23/05
probably wouldn't work as well once the plastic is baked
-
ENVYMYZ
14:55:35 11/23/05
you can buy eurathane remover which is used to strip -
AzHeat
16:34:41 11/23/05
Post a
Followup
You cannot reply to this message because you are not
logged in
.