Subject	aww man that sucks
Posted by	CollegeBoy on November 12, 2005 at 5:58 PM
	This message has been viewed 20 times.
In Reply To	no I built the whole motor and installed it posted by suprakillinz(boulder soon) on November 12, 2005 at 05:54 PM
Message	thats one of the many reasons I'm not so sure I want to build my engine myself. Might as well leave it up to a professional, then I can just install it. Good luck with everything man. Thanks, Mike 1991 Black Twin Turbo (Show AND Go) "lmao, i know, theres more drama and favoritism on tt.net than a middle school girls locker room" - sfpearl300z "I think I'll pass on giving my car a handjob" - joel(PA) "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - DC 21 "If I wanted a smooth ride, I would have bought a Lincoln."
Follow Ups	The good, the bad, and I need advice - suprakillinz(boulder soon) 16:09:40 11/12/05 Keep the car. - ssm300z 16:11:36 11/12/05 the stud is only a year old (n/m) - suprakillinz(boulder soon) 16:12:43 11/12/05 keep it (n/m) - WAGGZ 16:24:18 11/12/05 keep a broken car where for the next 2-3 years? - suprakillinz(boulder soon) 16:26:58 11/12/05 storage, back home, in a chicken barn, wherever. - WAGGZ 16:29:55 11/12/05 must be some big chickens.... - Zrevolver 16:56:37 11/12/05 Great words of wisdom, these words are. - WAGGZ 19:13:54 11/12/05 Broken upper stud - TXQ45 16:27:35 11/12/05 mine broke as well - spyhunter(nj) 16:35:47 11/12/05 keep it and wait til you get out of school to worry - charizma 16:31:23 11/12/05 Part it for extremely cheap to me:) (n/m) - 2960cc of fury (Houston) 16:32:16 11/12/05 so far no hate, this cant last much longer (n/m) - hey GotBo0st 16:42:47 11/12/05 valves can bend at idle - mousersix (San Antonio) 16:43:44 11/12/05 No, not the 900RWHP monster!!!.....:( yea right..... (n/m) - Gold Z 17:31:30 11/12/05 wow good luck man - IRISH 17:33:33 11/12/05 Studs usually break from over-tensioning the timing belt. - Ash's Z 17:46:50 11/12/05 any thoughts on why the cam gear can move 4-5 teeth - suprakillinz(boulder soon) 18:39:27 11/12/05 If its the inlet cam gears, could be the VVT - Tektrader69 16:16:02 11/13/05 That sucks, man...I would keep the car until I finish school - TheTwinZ (Peru) 17:48:21 11/12/05 did Rich install the belt? - aliaZ 17:50:28 11/12/05 Thats exactly what I was thinking - CollegeBoy 17:54:00 11/12/05 no I built the whole motor and installed it - suprakillinz(boulder soon) 17:54:17 11/12/05 aww man that sucks - CollegeBoy 17:58:13 11/12/05 oops (n/m) - aliaZ 19:15:00 11/12/05 Im curios of .... - Spddracer 21:10:00 11/12/05 that sucks man. i say keep it - CollegeBoy 17:52:10 11/12/05 Some serious advice for you: - RSR 18:21:26 11/12/05 smart man. (n/m) - josh 18:25:39 11/12/05 because I am trying to figure out what to do - suprakillinz(boulder soon) 18:35:27 11/12/05 I think you may have just answered your own question. - CMH (OH) 18:48:54 11/12/05 For once in my life I am making school a priority - suprakillinz(boulder soon) 18:58:08 11/12/05 blah, who wants to be done with school? - PennStateZ 22:11:44 11/12/05 Waggs is right, just keep it. If you get rid of it now - tyreeztt 18:57:39 11/12/05 How can I miss something I never drive? - suprakillinz(boulder soon) 18:59:20 11/12/05 Money spent on education is potentially the best investment - 240Z FeO2 20:41:07 11/12/05 Thread-jack - What is the "correct" way to install a stud - whitepearlz 02:59:08 11/13/05 Snug it & use LocTite. (n/m) - YugoBernie (NoVA) 03:18:24 11/13/05 Thanks. (n/m) - whitepearlz 09:22:32 11/13/05 that stud was never touched from the last build - suprakillinz(boulder soon) 16:27:14 11/13/05 pffft (n/m) - Rbadger 11:41:04 11/13/05
Post a Followup	You cannot reply to this message because you are not logged in.