Subject	I'll keep a close eye during the install
Posted by	ZEngineer on October 20, 2005 at 9:23 AM
	This message has been viewed 123 times.
In Reply To	The GMS kit was always a R33/R34 spec'd kit, in order to use posted by YugoBernie (NoVA) on October 20, 2005 at 09:15 AM
Message	if I need any spacers, I'll put some. Thanks for the heads-up. _________________________________________________________________________________ "The Z is the cause and the solution to all my problems" -- Me manstretch: well, my rear end is just worn out ZEngineer24: sig quote
Follow Ups	The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! - YugoBernie (NoVA) 23:13:37 10/19/05 can the drilled/sloted rotors be resurfaced if they - jalohafan 23:32:55 10/19/05 I have always heard NO. unless there is some special lathe (n/m) - Shawn300zTT GT28R MD 23:39:33 10/19/05 some shops will, some wont... - tyler@boostpro.net 23:50:42 10/19/05 quiet you. (n/m) - Shawn300zTT GT28R MD 00:10:48 10/20/05 don't be jealous. (n/m) - tyler@boostpro.net 01:18:15 10/20/05 lol, of what :) (n/m) - Shawn300zTT GT28R MD 22:47:59 10/20/05 I would not resurface rotors for a Z, drilled or not - PLEAZURE in CA (SD) 02:11:39 10/20/05 typically you are removing a VERY small ammount of material - AntiHero 08:10:56 10/20/05 They generally remove .010" to .025" depending on - jkeyser14 10:56:47 10/20/05 I've seen it done, ask machine shops in your area. (n/m) - YugoBernie (NoVA) 06:38:26 10/20/05 Let the shop know you're willing to pay a little extra - jkeyser14 10:59:06 10/20/05 Awesome. I may have to get in on this one. (n/m) - Zfreak(Dallas) 23:33:17 10/19/05 Could the 3kGT VR4 rotors work with this kit? - Zfreak(Dallas) 23:37:09 10/19/05 no it won't - different offset (n/m) - yellowzxtt 00:05:48 10/20/05 3KGT VR4 rotor vs. VIR Turn 1 - JohnC 00:15:28 10/20/05 that happens when you buy Ebay rotors (n/m) - yellowzxtt 04:05:18 10/20/05 Jacking the car up on sand... that's safe (n/m) - jkeyser14 11:00:41 10/20/05 No the VR4 rotors are 12.5" & have a different offset, they - YugoBernie (NoVA) 15:15:19 10/20/05 The top bracket is still a little bright! Just kidding don't - 300ZXquire 23:55:38 10/19/05 Re: The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! (n/m) - Chadztt 00:00:11 10/20/05 Re: The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! - Chadztt 00:02:03 10/20/05 Do you have prices on 2-peice rotors? - Shawn300zTT GT28R MD 00:10:27 10/20/05 More Money, around $500-600, that's just for front :( (n/m) - Coz@CZP 01:49:55 10/20/05 Like Coz said - we'd source those from StopTech prob. - YugoBernie (NoVA) 06:41:59 10/20/05 I'm curious... - whitepearlz 00:11:43 10/20/05 Dee Ridgeway has the Z1/Ash kit, 13" COBRA rotors etc - Shawn300zTT GT28R MD 01:00:12 10/20/05 I think it's the clearly the next significant step up from - YugoBernie (NoVA) 06:57:20 10/20/05 Thanks Bernie. (n/m) - whitepearlz 09:59:50 10/20/05 I am very interested but will they fit with M-Sports? (n/m) - DansZ 08:02:55 10/20/05 You need to do the math: - YugoBernie (NoVA) 08:34:37 10/20/05 im saying will the caliper hit the spokes? (n/m) - DansZ 12:26:47 10/20/05 If your stock brakes clear the spokes w/ 5mm or more - kuah@splparts.com 13:09:59 10/20/05 close call I will take some measurements. - DansZ 13:36:08 10/20/05 They will not fit w/o spacers - govaardz(Aruba) 14:48:02 10/20/05 Good job! Question inside: - ZEngineer 08:52:01 10/20/05 I have the GMS SKyline kit, the one before he did the - EricTTZ 09:10:03 10/20/05 The GMS kit was always a R33/R34 spec'd kit, in order to use - YugoBernie (NoVA) 09:15:16 10/20/05 I'll keep a close eye during the install - ZEngineer 09:23:42 10/20/05 It will be obvious if you are using the GMS bracket w. the - YugoBernie (NoVA) 09:39:08 10/20/05
Post a Followup	You cannot reply to this message because you are not logged in.