Subject	Good job! Question inside:
Posted by	ZEngineer on October 20, 2005 at 8:52 AM
	This message has been viewed 150 times.
In Reply To	The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! posted by YugoBernie (NoVA) on October 19, 2005 at 11:13 PM
Message	When you say "this kit does not require the use of shims or washers to space it for use w. the 350Z rotor.", are you saying that the GMS version of your kit did require shims, or are you referring to the Cobra adaptor kit? The reason I ask is because I have the GMS version but have not installed it yet, should I expect to use spacers & shims? _________________________________________________________________________________ "The Z is the cause and the solution to all my problems" -- Me manstretch: well, my rear end is just worn out ZEngineer24: sig quote
Follow Ups	The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! - YugoBernie (NoVA) 23:13:37 10/19/05 can the drilled/sloted rotors be resurfaced if they - jalohafan 23:32:55 10/19/05 I have always heard NO. unless there is some special lathe (n/m) - Shawn300zTT GT28R MD 23:39:33 10/19/05 some shops will, some wont... - tyler@boostpro.net 23:50:42 10/19/05 quiet you. (n/m) - Shawn300zTT GT28R MD 00:10:48 10/20/05 don't be jealous. (n/m) - tyler@boostpro.net 01:18:15 10/20/05 lol, of what :) (n/m) - Shawn300zTT GT28R MD 22:47:59 10/20/05 I would not resurface rotors for a Z, drilled or not - PLEAZURE in CA (SD) 02:11:39 10/20/05 typically you are removing a VERY small ammount of material - AntiHero 08:10:56 10/20/05 They generally remove .010" to .025" depending on - jkeyser14 10:56:47 10/20/05 I've seen it done, ask machine shops in your area. (n/m) - YugoBernie (NoVA) 06:38:26 10/20/05 Let the shop know you're willing to pay a little extra - jkeyser14 10:59:06 10/20/05 Awesome. I may have to get in on this one. (n/m) - Zfreak(Dallas) 23:33:17 10/19/05 Could the 3kGT VR4 rotors work with this kit? - Zfreak(Dallas) 23:37:09 10/19/05 no it won't - different offset (n/m) - yellowzxtt 00:05:48 10/20/05 3KGT VR4 rotor vs. VIR Turn 1 - JohnC 00:15:28 10/20/05 that happens when you buy Ebay rotors (n/m) - yellowzxtt 04:05:18 10/20/05 Jacking the car up on sand... that's safe (n/m) - jkeyser14 11:00:41 10/20/05 No the VR4 rotors are 12.5" & have a different offset, they - YugoBernie (NoVA) 15:15:19 10/20/05 The top bracket is still a little bright! Just kidding don't - 300ZXquire 23:55:38 10/19/05 Re: The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! (n/m) - Chadztt 00:00:11 10/20/05 Re: The Rebirth of the 350Z Track Edition 12.8" Rotor Kits! - Chadztt 00:02:03 10/20/05 Do you have prices on 2-peice rotors? - Shawn300zTT GT28R MD 00:10:27 10/20/05 More Money, around $500-600, that's just for front :( (n/m) - Coz@CZP 01:49:55 10/20/05 Like Coz said - we'd source those from StopTech prob. - YugoBernie (NoVA) 06:41:59 10/20/05 I'm curious... - whitepearlz 00:11:43 10/20/05 Dee Ridgeway has the Z1/Ash kit, 13" COBRA rotors etc - Shawn300zTT GT28R MD 01:00:12 10/20/05 I think it's the clearly the next significant step up from - YugoBernie (NoVA) 06:57:20 10/20/05 Thanks Bernie. (n/m) - whitepearlz 09:59:50 10/20/05 I am very interested but will they fit with M-Sports? (n/m) - DansZ 08:02:55 10/20/05 You need to do the math: - YugoBernie (NoVA) 08:34:37 10/20/05 im saying will the caliper hit the spokes? (n/m) - DansZ 12:26:47 10/20/05 If your stock brakes clear the spokes w/ 5mm or more - kuah@splparts.com 13:09:59 10/20/05 close call I will take some measurements. - DansZ 13:36:08 10/20/05 They will not fit w/o spacers - govaardz(Aruba) 14:48:02 10/20/05 Good job! Question inside: - ZEngineer 08:52:01 10/20/05 I have the GMS SKyline kit, the one before he did the - EricTTZ 09:10:03 10/20/05 The GMS kit was always a R33/R34 spec'd kit, in order to use - YugoBernie (NoVA) 09:15:16 10/20/05 I'll keep a close eye during the install - ZEngineer 09:23:42 10/20/05 It will be obvious if you are using the GMS bracket w. the - YugoBernie (NoVA) 09:39:08 10/20/05
Post a Followup	You cannot reply to this message because you are not logged in.