Subject	Basically the same thing, I tweaked mine a little
Posted by	DAYTONAZ on September 21, 2005 at 1:50 PM
	This message has been viewed 24 times.
In Reply To	Aluminum fuel line from Summit works great too. posted by Woody75 (Denver) on September 21, 2005 at 08:43 AM
Message	The left side pipe where it leaves the turbo and curves forward is the first place I modded it. I cut the pipe just above the standoff. On the right side I also cut the pipe just above the stop flare so I could lower the connection point. The same end result though and that engine of yours looks good.
Follow Ups	The engine is juuuust about done - DAYTONAZ 14:47:08 09/20/05 Engine gussets must go on before turbos - Joe(NoVA) 14:51:44 09/20/05 They're on there, thanks (n/m) - DAYTONAZ 14:56:17 09/20/05 Nice work! Cant wait to see it all done (n/m) - Madhatter10-6 14:53:06 09/20/05 congrats...nice work on the coolant lines. (n/m) - Zeus 15:15:32 09/20/05 any luck finding a chassis? (n/m) - dpjax 15:26:58 09/20/05 looks beautiful!!! Needs a new oil cap :) (n/m) - Slobo7x 15:41:17 09/20/05 I know, I'll take care of that this weekend too. (n/m) - DAYTONAZ 17:02:49 09/20/05 Re: The engine is juuuust about done - ZheKing 16:15:07 09/20/05 nice...any plans with the throttle bodies? - atl300zxtt 16:26:30 09/20/05 I was thinking the same thing as I closed the garage - DAYTONAZ 17:01:56 09/20/05 what? you dont want to pull the plenum? :) (n/m) - atl300zxtt 07:20:01 09/21/05 CAn they be removed without pulling the plenum? - atl300zxtt 07:21:25 09/21/05 Just painted them red this morning, they look good :-) (n/m) - DAYTONAZ 13:52:04 09/21/05 any pics? (n/m) - atl300zxtt 08:54:50 09/22/05 I really like how you ran the water lines for the turbos - whitepearlz 16:39:36 09/20/05 Napa 5/16" pre flared tubing. - DAYTONAZ 17:00:03 09/20/05 Nice. (n/m) - YugoBernie (NoVA) 17:06:01 09/20/05 sweet (n/m) - Zeus 17:12:32 09/20/05 I just might have to try that. Thanks. (n/m) - whitepearlz 17:13:25 09/20/05 Aluminum fuel line from Summit works great too. - Woody75 (Denver) 08:43:58 09/21/05 Basically the same thing, I tweaked mine a little - DAYTONAZ 13:50:45 09/21/05 Thats not my engine, it's a customers. - Woody75 (Denver) 14:52:05 09/21/05 Dam that hose, mine was torn in the exact same spot - 2960cc of fury (Houston) 17:07:43 09/20/05 Dude forget scrubbing the engine bay - suprakillinz(boulder soon) 17:19:00 09/20/05 That's what I was planning on doing less the power wash - DAYTONAZ 17:39:43 09/20/05 2nd Simple Green + Clean Rags = Nice (n/m) - Turnerscasa (Dallas) 12:02:57 09/21/05 I have an inlet pipe I could send- (n/m) - MyDreamZ 18:21:22 09/20/05 Looks great! I think it'd look great with black water pipes - Scotts94z32 21:00:08 09/20/05 I bought the silicone rad hoses - DAYTONAZ 13:40:20 09/21/05 looks saweet.... - tyler@boostpro.net 22:58:51 09/20/05 Re: The engine is juuuust about done - ____DETT 01:35:51 09/21/05 2nd Simple Green + Clean Rags = Nice (n/m) - Turnerscasa (Dallas) 12:00:43 09/21/05 Nice job! Looks great! (n/m) - 15zcar 13:28:18 09/21/05
Post a Followup	You cannot reply to this message because you are not logged in.