Subject	Napa 5/16" pre flared tubing.
Posted by	DAYTONAZ on September 20, 2005 at 5:00 PM
	This message has been viewed 78 times.
In Reply To	I really like how you ran the water lines for the turbos posted by whitepearlz on September 20, 2005 at 04:39 PM
Message	I bought a section at 48". Cut the flares off and lose the b-nuts. I used a manual tubing bender I borrowed from work. Makes quick work of the bends. While your at Napa pick up a foot of 5/16" hose for the connectors. I had some left over spring clamps from the hoses I deleted under the plenum so I used those to secure the pipes. The run on the left side is kinda long so you'll need some type of clamp to secure the pipe against vibration. The pipe on the right is short and doesn't require a stand-off.
Follow Ups	The engine is juuuust about done - DAYTONAZ 14:47:08 09/20/05 Engine gussets must go on before turbos - Joe(NoVA) 14:51:44 09/20/05 They're on there, thanks (n/m) - DAYTONAZ 14:56:17 09/20/05 Nice work! Cant wait to see it all done (n/m) - Madhatter10-6 14:53:06 09/20/05 congrats...nice work on the coolant lines. (n/m) - Zeus 15:15:32 09/20/05 any luck finding a chassis? (n/m) - dpjax 15:26:58 09/20/05 looks beautiful!!! Needs a new oil cap :) (n/m) - Slobo7x 15:41:17 09/20/05 I know, I'll take care of that this weekend too. (n/m) - DAYTONAZ 17:02:49 09/20/05 Re: The engine is juuuust about done - ZheKing 16:15:07 09/20/05 nice...any plans with the throttle bodies? - atl300zxtt 16:26:30 09/20/05 I was thinking the same thing as I closed the garage - DAYTONAZ 17:01:56 09/20/05 what? you dont want to pull the plenum? :) (n/m) - atl300zxtt 07:20:01 09/21/05 CAn they be removed without pulling the plenum? - atl300zxtt 07:21:25 09/21/05 Just painted them red this morning, they look good :-) (n/m) - DAYTONAZ 13:52:04 09/21/05 any pics? (n/m) - atl300zxtt 08:54:50 09/22/05 I really like how you ran the water lines for the turbos - whitepearlz 16:39:36 09/20/05 Napa 5/16" pre flared tubing. - DAYTONAZ 17:00:03 09/20/05 Nice. (n/m) - YugoBernie (NoVA) 17:06:01 09/20/05 sweet (n/m) - Zeus 17:12:32 09/20/05 I just might have to try that. Thanks. (n/m) - whitepearlz 17:13:25 09/20/05 Aluminum fuel line from Summit works great too. - Woody75 (Denver) 08:43:58 09/21/05 Basically the same thing, I tweaked mine a little - DAYTONAZ 13:50:45 09/21/05 Thats not my engine, it's a customers. - Woody75 (Denver) 14:52:05 09/21/05 Dam that hose, mine was torn in the exact same spot - 2960cc of fury (Houston) 17:07:43 09/20/05 Dude forget scrubbing the engine bay - suprakillinz(boulder soon) 17:19:00 09/20/05 That's what I was planning on doing less the power wash - DAYTONAZ 17:39:43 09/20/05 2nd Simple Green + Clean Rags = Nice (n/m) - Turnerscasa (Dallas) 12:02:57 09/21/05 I have an inlet pipe I could send- (n/m) - MyDreamZ 18:21:22 09/20/05 Looks great! I think it'd look great with black water pipes - Scotts94z32 21:00:08 09/20/05 I bought the silicone rad hoses - DAYTONAZ 13:40:20 09/21/05 looks saweet.... - tyler@boostpro.net 22:58:51 09/20/05 Re: The engine is juuuust about done - ____DETT 01:35:51 09/21/05 2nd Simple Green + Clean Rags = Nice (n/m) - Turnerscasa (Dallas) 12:00:43 09/21/05 Nice job! Looks great! (n/m) - 15zcar 13:28:18 09/21/05
Post a Followup	You cannot reply to this message because you are not logged in.