Subject	On paper it sounds like THE way to do it>>>
Posted by	zboost(tx) on September 06, 2005 at 10:24 PM
	This message has been viewed 27 times.
In Reply To	I have read that AMG dynos all their hand-built engines posted by olyar15 on September 06, 2005 at 10:18 PM
Message	because the rings would seat better, but my hairs just raise thinking of that brand new $10K engine spinning at redline and going boom. :) "yo yo. writing this one in jail - tight300zx" I hope you got soap on a rope?? (n/m) - Spongerider :) 19:14:08 04/01/04 we'll know if the screen name changes ;) (n/m) - SactoTodd 19:32:36 04/01/04 "I did plug the holes, But I did it by taping over them a lot, I didnt think that maybe HOT air is comming through there, And it melted the tape, damnit im an ass." - - DC 21:11:01 02/18/04 (the "holes" were located on the exhaust)
Follow Ups	Breaking in engine - Joe(NoVA) 21:10:20 09/06/05 Ash is breaking his in on the dyno. - zboost(tx) 21:20:35 09/06/05 I have read that AMG dynos all their hand-built engines - olyar15 22:18:52 09/06/05 On paper it sounds like THE way to do it>>> - zboost(tx) 22:24:21 09/06/05 No, thats a different situation - Joe(NoVA) 07:15:18 09/07/05 I broke mine in on the Dyno as well. (n/m) - Zfreak(Omaha) 22:29:22 09/06/05 Aside from piston seal - Joe(NoVA) 07:25:18 09/07/05 Joe, You still up? I just drove my (similar to your) set up - SirpriZ 22:26:38 09/06/05 I'll give you a call later in the week :-) (n/m) - Joe(NoVA) 07:19:00 09/07/05 If you break it.... - Scotts94z32 10:43:52 09/07/05 Will it feel like a pu**y, that's what I'm "shooting" for! - SirpriZ 00:21:19 09/08/05 This is the method... - tyler@boostpro.net 22:33:53 09/06/05 God no - Joe(NoVA) 07:42:25 09/07/05 Re: God no - Russ ZTT (Jax, Fl) 09:06:30 09/07/05 What are your opinions about this? - Joe(NoVA) 09:59:23 09/07/05 Hard to take seriously when they misspell "laser" (n/m) - Technomancer 10:02:06 09/07/05 That's really all you can take from that? (n/m) - Joe(NoVA) 10:06:11 09/07/05 No - Technomancer 10:31:18 09/07/05 I agree with you - Joe(NoVA) 10:40:54 09/07/05 Or this? - Joe(NoVA) 10:04:32 09/07/05 I don't care about 4hp - Joe(NoVA) 10:10:10 09/07/05 talk to your machinist, see how they recomend breakin in.... - madtdogs 17:46:23 09/07/05 Kyle @ SGP (who built my motor) recommended what i posted - Joe(NoVA) 19:23:01 09/07/05 Follow Randy around for a 1/2 day thru cincy :() (n/m) - Spddracer 19:51:26 09/07/05
Post a Followup	You cannot reply to this message because you are not logged in.